Nissan X-Trail 32. Instruction — part 1462
ROOM LAMP
INL-85
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
REMOVAL
1.
Apply protective tape (A) to room lamp housing for protecting it
from damage.
2.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens.
3.
Press metal clip
using a remover tool (A) to disengage metal
clips.
4.
Pull downward room lamp housing, and then disengage room
lamp fixing pawls.
CAUTION:
Never damage the headlining assembly.
5.
Disconnect harness connector, and then remove room lamp housing.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010755171
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-4, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
ROOM LAMP BULB
JMLIA3195ZZ
: Pawl
JMLIA3196ZZ
: Pawl
: Metal clip
JMLIA1801ZZ
INL-86
< REMOVAL AND INSTALLATION >
ROOM LAMP
1.
Apply protective tape (A) to room lamp housing for protecting it
from damage.
2.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens.
3.
Remove bulb.
JMLIA3195ZZ
: Pawl
JMLIA3196ZZ
PERSONAL LAMP
INL-87
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PERSONAL LAMP
Exploded View
INFOID:0000000010755172
Removal and Installation
INFOID:0000000010755173
REMOVAL
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-4, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
• Remove personal lamp base LH and RH as a set.
1.
Remove headlining assembly. Refer to
INT-37, "Removal and Installation"
.
Personal lamp base
Personal lamp finisher
Bulb
Lens
: Pawl
: Vehicle front
JMLIA4275ZZ
INL-88
< REMOVAL AND INSTALLATION >
PERSONAL LAMP
2.
Disengage personal lamp finisher fixing pawls using a remover
tool (A).
3.
Disengage personal lamp finisher fixing pawls according to
numerical order 1
→
2 indicated by arrows as shown in the figure,
and then remove personal lamp finisher.
4.
Remove personal lamp base from headlining assembly.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010755174
PERSONAL LAMP BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-4, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
1.
Apply protective tapes (A) to personal lamp finisher for protect-
ing it from damage.
: Pawl
JMLIA3627ZZ
: Pawl
JMLIA3628ZZ
JMLIA3629ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст