Nissan X-Trail 32. Instruction — part 2244
FRONT WIPER
WW-83
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
2.
Remove front wiper arm cap.
3.
Remove front wiper arm mouonting nut, and then remove front wiper arm.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Clean front wiper arm installation location as shown in the fig-
ure, and then fully insert front wiper arm to prevent nut from
being loosened by shakiness.
• When installing front wiper arm, install so that it is within the standard. For the standard, refer to
WW-83, "WIPER ARM : Adjustment"
.
• After installation, operate front wiper, and then check that front wiper blades stop at the specified
position. Refer to
WW-83, "WIPER ARM : Adjustment"
WIPER ARM : Adjustment
INFOID:0000000010785448
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover / front fender cover and the top of front wiper blade center.
: pawl
JMLIA4840ZZ
ELH0717D
Windshield glass
Front wiper blade RH
Front wiper blade LH
Cowl top cover
Front fender cover LH
JMLIA4841ZZ
WW-84
< REMOVAL AND INSTALLATION >
FRONT WIPER
Standard clearance
WIPER BLADE
WIPER BLADE : Removal and Installation
INFOID:0000000010785449
CAUTION:
Clean the windshield glass and front wiper refill so that the windshield glass may not be damaged by
dust, etc.
REMOVAL
1.
Move front wiper arm by service position operation to lock back possibility position.
• With rain sensor: Refer to
WW-13, "FRONT WIPER AND WASHER SYSTEM (WITH LIGHT & RAIN
.
• Without rain sensor: Refer to
WW-17, "FRONT WIPER AND WASHER SYSTEM (WITHOUT LIGHT &
RAIN SENSOR) : System Description"
.
2.
Lift up front wiper arm, and then lock back front wiper arm.
3.
Slide the wiper brade
while pushing the lever
according to
the numerical order 1
→
2 as shown in the figure from front wiper
arm .
CAUTION:
After the wiper brade is removed, wrap the wiper arm tip
with a shop cloth and fold it down so that the wiper arm
does not fall against and damage the windshield glass.
INSTALLATION
Install in the reverse order of removal.
WIPER REFILL
WIPER REFILL : Removal and Installation
INFOID:0000000010785450
REMOVAL
1.
Remove front wiper blade. Refer to
WW-84, "WIPER BLADE : Removal and Installation"
2.
Pull out front wiper refill using a long-nose pliers (A), and then
remove front wiper refill.
INSTALLATION
C
: 34.88
±
7.5 mm (1.37
±
0.30 in)
D
: 38.20
±
7.5 mm (1.50
±
0.30 in)
JMLIA0833ZZ
JMLIA4385ZZ
FRONT WIPER
WW-85
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
1.
Check the front wiper refill insertion direction by arrow mark on
front wiper blade.
2.
Pass through pawl of front wiper blade in the groove of front
wiper refill.
NOTE:
Remove holder
* at last procedure.
*: Attached to service parts.
3.
Engage front wiper refill stopper hole, and front wiper blade pawl with imprinted “SET” mark (“
” mark).
4.
Check the following items after installing.
• Front wiper refill thoroughly fits in the pawl on front wiper blade.
• Front wiper refill is not deformed (waving / tucking).
NOTE:
When the vertebra is detached
• Insert the vertebra
into the front wiper blade to the same bend-
ing direction.
• If a vertebra has a notch, fit it to a protrusion inside the front wiper
refill.
WIPER DRIVE ASSEMBLY
WIPER DRIVE ASSEMBLY : Removal and Installation
INFOID:0000000010785451
REMOVAL
1.
Remove cowl top cover. Refer to
EXT-25, "Removal and Installation"
.
JMLIA2606ZZ
JMLIA4386ZZ
JPLIA1586ZZ
WW-86
< REMOVAL AND INSTALLATION >
FRONT WIPER
2.
Disconnect front wiper motor harness connector
.
3.
Remove front wiper drive assembly mounting bolts
, and then
remove front wiper drive assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing, temporarily tighten all mounting bolts, and then tighten bolts to specified torque.
WIPER DRIVE ASSEMBLY : Disassembly and Assembly
INFOID:0000000010785452
DISASSEMBLY
1.
Remove front wiper linkage 1 and 2 from front wiper flame.
CAUTION:
Never bend the link or damage the plastic part of the ball joint when removing front wiper linkage.
2.
Remove front wiper motor bracket mounting bolts, and then remove front wiper motor from front wiper
flame.
ASSEMBLY
Note the following items, and assembly in the reverse order of disassembly.
CAUTION:
• When front wiper motor is replaced, before installing front wiper arm, operate front wipers, set front
wiper motor to the auto stop position, and then install front wiper arms.
• Be careful for grease condition at front wiper linkage joint (retainer), apply Multi-purpose grease or
an equivalent if necessary.
JMLIA5002ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст