Nissan Teana J32. Instruction — part 1134
TM-60
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0730 BELT DAMAGE
P0730 BELT DAMAGE
Description
INFOID:0000000003848973
TCM selects the gear ratio using the engine load (throttle position), the primary pulley revolution speed, and
the secondary pulley revolution speed as input signals. Then it changes the operating pressure of the primary
pulley and the secondary pulley and changes the groove width of the pulley.
DTC Logic
INFOID:0000000003848974
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Make sure that output voltage of CVT fluid temperature sensor is within the range below.
4.
Start engine and maintain the following conditions for at least 30 consecutive seconds.
Is “P0730 BELT DAMG” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003848975
1.
CHECK DTC
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “Self-Diagnostic Results” mode for “TRANSMISSION”.
Are any DTC detected?
YES-1 (DTC for “P0730 BELT DAMG” is detected)>>Replace transaxle assembly. Refer to
.
YES-2 (DTC except for “P0730 BELT DAMG” is detected)>>Check DTC detected item. Refer to
"CONSULT-III Function (TRANSMISSION)"
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING ITEMS
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0730
BELT DAMG
Unexpected gear ratio detected.
Transaxle assembly
ATF TEMP SEN
: 1.0 – 2.0 V
If it is out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage
(cool down the fluid)
Start test from 0 km/h (0 MPH)
Constant acceleration
: Keep 30 sec or more
VEHICLE SPEED
: 10 km/h (6 MPH) or more
ACC PEDAL OPEN
: More than 1.0/8
RANGE
: “D” position
ENG SPEED
: 450 rpm or more
P0730 BELT DAMAGE
TM-61
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
TM-62
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
Description
INFOID:0000000003848976
• The torque converter clutch solenoid valve is activated by the TCM in response to signals sent from the vehi-
cle speed and accelerator pedal position sensors. Lock-up piston operation will then be controlled.
• Lock-up operation, however, is prohibited when CVT fluid temperature is too low.
• When the accelerator pedal is depressed (less than 2.0/8) in lock-up condition, the engine speed shall not
change abruptly. If there is a big jump in engine speed, there is no lock-up.
DTC Logic
INFOID:0000000003848977
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Wait at least 10 consecutive seconds.
3.
Perform “Self-Diagnostic Results” mode for “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0740 TCC SOLENOID/CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003848978
1.
CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check resistance between TCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (TORQUE CONVERTER CLUTCH SOLENOID
VALVE) (PART 1)
1.
Disconnect CVT unit connector.
2.
Check continuity between TCM vehicle side harness connector terminal and CVT unit vehicle side har-
ness connector terminal.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P0740
TCC SOLENOID/CIRC
Normal voltage is not applied to solenoid
due to open or short circuit.
• Torque converter clutch solenoid valve
• Harness or connectors
(Solenoid circuit is open or shorted.)
TCM vehicle side harness connector
Ground
Resistance (Approx.)
Connector
Terminal
F23
38
3.0 – 9.0
Ω
P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE
TM-63
< COMPONENT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (TORQUE CONVERTER CLUTCH SOLENOID
VALVE) (PART 2)
Check continuity between TCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE
Check torque converter clutch solenoid valve. Refer to
TM-63, "Component Inspection (Torque Converter
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace transaxle assembly. Refer to
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
Component Inspection (Torque Converter Clutch Solenoid Valve)
INFOID:0000000003848979
1.
CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace transaxle assembly. Refer to
TCM vehicle side harness connector
CVT unit vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F23
38
F24
12
Existed
TCM vehicle side harness connector
Ground
Continuity
Connector
Terminal
F23
38
Not existed
CVT unit connector
Ground
Resistance (Approx.)
Connector
Terminal
F24
12
3.0 – 9.0
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст