Nissan Teana J32. Instruction — part 1101
STEERING WHEEL
ST-11
< ON-VEHICLE MAINTENANCE >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
5.
Check the following items when turning angle is out of the stan-
dard.
a.
Check the neutral position of the rack stroke (L).
b.
Disassemble steering gear assembly to check the cause that
rack stroke is outside of the standard.
• Steering angles are not adjustable. Check steering gear
assembly, steering column assembly and front suspension
components for wear or damage if any of the turning angles are different from the specified value.
Replace any of them, if any non-standard condition exists.
Standard
L
: Refer to
.
SGIA0629J
ST-12
< ON-VEHICLE REPAIR >
STEERING WHEEL
ON-VEHICLE REPAIR
STEERING WHEEL
Exploded View
INFOID:0000000003806314
Removal and Installation
INFOID:0000000003806315
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1.
Set the vehicle to the straight-ahead position.
2.
Remove driver air bag module. Refer to
.
3.
Remove steering wheel lock nut after steering is locked.
4.
Remove steering wheel with the steering wheel puller (A) (SST:
ST27180001).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never twist spiral cable freely on excessively after it becomes tight (doing so may cause the cable to
tear off).
NOTE:
Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
.
1.
Steering wheel
Refer to
for symbols in the figure.
JSGIA0303GB
JSGIA0391ZZ
STEERING COLUMN
ST-13
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Exploded View
INFOID:0000000003806316
Removal and Installation
INFOID:0000000003806317
REMOVAL
1.
Set the vehicle to the straight-ahead position.
2.
Place the tilt to the highest level.
3.
Remove driver air bag module. Refer to
.
4.
Remove steering wheel. Refer to
.
5.
Remove the instrument driver lower panel. Refer to
.
6.
Remove the steering column cover. Refer to
.
7.
Remove spiral cable. Refer to
.
8.
Remove combination switch. Refer to
1.
Steering column assembly
2.
Clip
3.
Clip
4.
Upper joint
5.
Spring
Refer to
JSGIA0386GB
ST-14
< ON-VEHICLE REPAIR >
STEERING COLUMN
9.
Remove knee protector (1).
10. Disconnect each switch harness connectors installed to steering
column assembly.
11. Remove the upper joint mounting bolt and nut (lower shaft side),
and separate the joint from lower shaft.
12. Remove steering column assembly.
CAUTION:
• Never give axial impact to steering column assembly dur-
ing removal.
• Never move steering gear assembly when removing steering column assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Make sure there is no space between clip (1) and steering column assembly (2).
CAUTION:
Never reuse the clip.
• Tighten the mounting nuts in the order shown in the figure steering
member (1) when installing the steering column assembly (2).
• Be careful of the following points when installing the steering col-
umn assembly.
CAUTION:
• Never give axial impact to steering column assembly during
installation.
• Never move steering gear assembly.
• Never reuse the joint mounting nut (lower shaft side).
• Adjust neutral position of steering angle sensor. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Special Repair Requirement"
(VDC models).
Inspection
INFOID:0000000003806318
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if necessary.
• Measure steering column assembly rotating torque using a preload gauge (SST: ST3127S000). Replace
steering column assembly if outside the standard.
: Bolt
JSGIA0344ZZ
JSGIA0346ZZ
JSGIA0387ZZ
Standard
Rotating torque
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст