Nissan Teana J32. Instruction — part 915
DOOR SWITCH
PWC-27
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
DOOR SWITCH
Description
INFOID:0000000003857784
Detects door open/closed condition.
Component Function Check
INFOID:0000000003857785
1.
CHECK FUNCTION
Check front door switches (“DOOR SW-DR”, “DOOR SW-AS”) in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES
>> Front door switch is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000003857786
1.
CHECK FRONT DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect malfunction front door switch connector.
3.
Check signal between malfunction front door switch harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT DOOR SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and malfunctioning front door switch harness connec-
tor.
3.
Check continuity between BCM harness connector and ground.
Monitor item
Door condition
Display
DOOR SW-DR
CLOSE
→
OPEN
OFF
→
ON
DOOR SW-AS
(+)
(–)
Voltage (V)
(Approx.)
Front door switch
Connector
Terminal
Driver side
B34
2
Ground
Passenger side
B220
JPMIA0011GB
BCM
Front door switch
Continuity
Connector
Terminal
Connector
Terminal
M123
124
B220
2
Exists
150
B34
PWC-28
< COMPONENT DIAGNOSIS >
DOOR SWITCH
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK FRONT DOOR SWITCH
Check front door switch.
Refer to
PWC-28, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunction front door switch. Refer to
DLK-234, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000003857787
1.
CHECK FRONT DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect malfunction front door switch connector.
3.
Check front door switch.
Is the inspection result normal?
YES
>> Front door switch is OK.
NO
>> Replace malfunctioning front door switch. Refer to
DLK-234, "Removal and Installation"
BCM
Ground
Continuity
Connector
Terminal
M123
124
Not exist
150
(+)
(-)
Condition
Continuity
Front door switch
Connector
Terminal
Driver side
B34
2
Ground part of
front door
switch
Door switch pressed
Not exists
Door switch released
Exists
Passenger side
B220
Door switch pressed
Not exists
Door switch released
Exists
ENCODER CIRCUIT
PWC-29
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ENCODER CIRCUIT
Description
INFOID:0000000003826026
Detects condition of the front power window motor (driver side) operation and transmits to power window main
switch as pulse signal.
Component Function Check
INFOID:0000000003826027
1.
CHECK ENCODER OPERATION
Check front driver side door glass and perform AUTO open/close operation normally via power window main
switch.
Is the inspection result normal?
YES
>> Encoder operation is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000003826028
Encoder Circuit Check
1.
CHECK ENCODER SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between power window main switch harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-85, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK ENCODER SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and front power window motor (driver side) connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
(+)
(–)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D5
9
Ground
Refer to the following signal
13
JMKIA0220GB
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
9
D7
3
Existed
13
5
PWC-30
< COMPONENT DIAGNOSIS >
ENCODER CIRCUIT
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK ENCODER POWER SUPPLY
1.
Connect power window main switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
3.
Check continuity between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (driver side). Refer to
GW-20, "Removal and Installation"
NO
>> Repair or replace harness.
5.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
3.
Check continuity between power window main switch harness connector and ground.
Power window main switch
Ground
Continuity
Connector
Terminal
D5
9
Not existed
13
(+)
(–)
Voltage (V)
(Approx.)
Front power window motor (driver side)
Connector
Terminal
D7
4
Ground
Battery voltage
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
2
D7
6
Existed
Front power window motor (driver side)
Ground
Continuity
Connector
Terminal
D7
6
Not existed
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
15
D7
4
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D5
15
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст