Nissan Teana J32. Instruction — part 935
RF-6
< FUNCTION DIAGNOSIS >
SUNROOF SYSTEM
Before Operation
Switch condition
Roof and sunshade operation
After Operation
OPEN: 1st
Opens the sunshade
OPEN: 2nd
The sunshade opens, and
then the sunroof opens.
PUSH
The sunshade opens, and
then the sunroof tilts up.
OPEN: 1st
Opens the sunroof
PUSH
Tilts down
CLOSE: 1st
CLOSE: 2nd
The sunroof tilts down, and
then sunshade closes.
JMKIA2617GB
JMKIA2619ZZ
JMKIA2620ZZ
JMKIA2621ZZ
JMKIA2627GB
JMKIA2628ZZ
JMKIA2618GB
JMKIA2622ZZ
JMKIA2623ZZ
SUNROOF SYSTEM
RF-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
AUTO OPERATION
The sunroof or sunshade operates automatically to the fully-open or fully-closes position by operating the sun-
roof switch to the OPEN (2nd) or CLOSE (2nd) position.
RETAINED POWER OPERATION
Retained power operation is an additional power supply function that enables sunroof system to operate for 45
seconds after ignition switch is turned OFF.
RETAINED POWER FUNCTION CANCEL CONDITIONS
• Front door CLOSE (door switch OFF)
→
OPEN (door switch ON)
• Ignition switch is ON again.
• Timer passed. (45 seconds)
ANTI-PINCH FUNCTION
CAUTION:
There are some small distances immediately before the closed position which cannot be detected.
• The CPU of sunroof motor assembly monitors the sunroof condition using the signals from sunroof motor.
When sunroof motor assembly detects an interruption during auto operation (close or tilt down operation),
sunroof motor will tilt up or open [150 mm (5.91 in) or more] sunroof.
• The CPU of sunshade motor assembly monitors the sunshade condition using the signals from sunshade
motor. When sunshade motor assembly detects an interruption during auto close operation, sunshade motor
will open [150 mm (5.91 in) or more] sunshade.
PUSH
Tilts up
CLOSE: 1st
Closes the sunroof
CLOSE: 2nd
The sunroof closes, and then
the sunshade closes.
CLOSE: 1st
Closes the sunshade
Before Operation
Switch condition
Roof and sunshade operation
After Operation
JMKIA2624GB
JMKIA2625ZZ
JMKIA2622ZZ
JMKIA2626ZZ
JMKIA2627GB
JMKIA2629ZZ
RF-8
< FUNCTION DIAGNOSIS >
SUNROOF SYSTEM
Component Parts Location
INFOID:0000000003812846
Component Description
INFOID:0000000003812847
1.
BCM M118, M119, M123
2.
Combination meter M34
3.
Sunroof motor assembly R101
4.
Sunshade motor assembly R102
5.
Sunroof switch R6
6.
Front door switch (driver side) B34
A.
Behind the combination meter
B.
Behind headlining
JMKIA2348ZZ
Component
Function
BCM
• Supplies power to sunroof motor assembly and sunshade motor assembly.
• Controls retained power function.
Combination meter
Transmits vehicle speed signal to sunroof motor assembly and sunshade motor assembly.
Sunroof motor assembly
The sunroof motor and CPU integrated type enable tilt up/down and slide open/close sunroof op-
eration by sunroof switch operation. And sends sunroof switch operation signal to sunshade mo-
tor assembly via communication line.
Sunshade motor assembly
The sunshade motor and CPU integrated type enable open/close sunshade operation by sunroof
switch operation.
Sunroof switch
Transmits switch operation signal to sunroof motor assembly.
Front door switch
(driver side/passenger side)
Detects door open/close condition and transmits to BCM.
DIAGNOSIS SYSTEM (BCM)
RF-9
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000003812848
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1:At model with Intelligent Key system this item is displayed, but is not used.
• *2: This item is displayed, but is not used.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion instruction.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT*
1
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
2
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
TPMS (AIR PRESSURE MONITOR)
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст