Nissan Teana J32. Instruction — part 1158
TM-156
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
CONTROL DEVICE
2.
Slide knob cover (1) below selector lever downward.
CAUTION:
Be careful not to damage knob cover.
3.
Pull lock pin (2) out of selector lever knob (3).
4.
Remove selector lever knob and knob cover.
5.
Remove center console assembly. Refer to
.
6.
Remove control cable (1) from control device assembly. Refer to
7.
Remove control device assembly (2).
8.
Remove control device connector (A) using a flat-bladed screw-
driver (B).
CAUTION:
Be careful not to damage control device connector.
9.
Remove shift lock unit from control device assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing control cable (1) to control device assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.
Inspection and Adjustment
INFOID:0000000003849090
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing control device. Refer to
TM-152, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-152, "Inspection and Adjustment"
JPDIA0606ZZ
: Bolt
JPDIA0615ZZ
JPDIA0616ZZ
JPDIA0609ZZ
CONTROL CABLE
TM-157
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL CABLE
Exploded View
INFOID:0000000003849091
Removal and Installation
INFOID:0000000003849092
REMOVAL
CAUTION:
Check that parking brake is applied before removal/installation.
1.
Disconnect control cable from control device assembly. Refer to
2.
Remove the air duct (inlet) and air cleaner case. Refer to
.
3.
Remove control cable (1) from instruction lever (A).
4.
Remove lock plate (2) from control cable.
5.
Remove control cable from bracket 2 (3).
6.
Remove exhaust front tube. Refer to
7.
Remove heat plate.
1.
Bracket 1
2.
Lock plate
3.
Bracket 2
4.
Transaxle assembly
5.
Control cable
6.
Control device assembly
Refer to
JPDIA0749GB
: Nut
JPDIA0601ZZ
TM-158
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
CONTROL CABLE
8.
Remove control cable (1) from bracket 1 (2).
9.
Remove nuts (
).
10. Remove rear foot duct 1 (right). Refer to
11. Remove the control cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing the control cable (1) to the control device assembly
(2), make sure that the control cable is fully pressed in with the
ribbed (A) surface facing upward.
Inspection and Adjustment
INFOID:0000000003849093
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing control cable. Refer to
TM-152, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-152, "Inspection and Adjustment"
: Vehicle front
JPDIA0752ZZ
JPDIA0609ZZ
OIL PAN
TM-159
< ON-VEHICLE REPAIR >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000003849094
Removal and Installation
INFOID:0000000003849095
REMOVAL
1.
Remove drain plug.
2.
Remove O-ring from drain plug.
3.
Remove oil pan fitting bolts (
).
4.
Remove oil pan.
1.
Transaxle assembly
2.
Oil pan fitting bolt
3.
Drain plug
4.
O-ring
5.
Oil pan
6.
Oil pan gasket
7.
Magnet
: Apply CVT Fluid NS-2.
Refer to
JPDIA0608GB
: Vehicle front
SCIA8135J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст