Nissan Teana J32. Instruction — part 479
EM-40
< ON-VEHICLE REPAIR >
OIL PAN AND OIL STRAINER
20. Loosen mounting bolts in the reverse order as shown in the fig-
ure to remove.
• Insert the seal cutter [SST: KV10111100 (J37228)] between oil
pan (upper) and cylinder block. Slide seal cutter by tapping on
the side of tool with a hammer. Remove oil pan (upper).
CAUTION:
• Be careful not to damage the mating surfaces.
• Never insert a screwdriver, this will damage the mating
surfaces.
21. Remove O-rings (2) from bottom of cylinder block (1) and oil
pump (3).
22. Remove oil pan gaskets (1).
INSTALLATION
1.
Install oil pan (upper) as follows:
a.
Use a scraper to remove old liquid gasket from mating surfaces.
CAUTION:
Never scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
• Also remove old liquid gasket from mating surface of cylinder
block.
• Remove old liquid gasket from the bolt holes and threads.
b.
Install new oil pan gaskets.
PBIC1636E
: Engine front
JPBIA1379ZZ
A
: Notch
B
: Protrusion
: Engine front
JPBIA0433ZZ
MEM108A
OIL PAN AND OIL STRAINER
EM-41
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Apply liquid gasket to new oil pan gaskets as shown in the fig-
ure.
Use Genuine Liquid Gasket or equivalent.
• To install, align protrusion (B) of oil pan gasket with notches
(A) of front timing chain case and rear oil seal retainer.
• Install oil pan gasket (1) with smaller arc to front timing chain
case side.
c.
Install new O-rings (2) on the bottom of cylinder block (1) and oil
pump (3).
d.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to the cylinder block mating surface of
oil pan (upper) to a limited portion as shown in the figure.
Use Genuine Liquid Gasket or equivalent.
CAUTION:
• For bolt holes with marks (5 locations), apply liquid
gasket outside the holes.
• Apply a bead of 4.5 to 5.5 mm (0.177 to 0.217 in) diameter to area (a).
• Attaching should be done within 5 minutes after coating.
e.
Install oil pan (upper).
CAUTION:
Install avoiding misalignment of both O-rings.
C
: Sealing point
a
: 15 mm (0.59 in)
b
: 5 mm (0.20 in)
JPBIA0432ZZ
: Engine front
JPBIA0433ZZ
: Engine front
JPBIA1379ZZ
b
: 35 mm (1.38 in)
c
:
φ
3.5 - 4.5 mm (0.138 - 0.177 in)
: Engine front
JPBIA0434ZZ
EM-42
< ON-VEHICLE REPAIR >
OIL PAN AND OIL STRAINER
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
• There are two types of mounting bolts. Refer to the following
for locating bolts.
2.
Install oil strainer to oil pump.
3.
Install oil pan (lower) as follows:
a.
Use scraper (A) to remove old liquid gasket from mating sur-
faces.
• Remove old liquid gasket from the bolt holes and thread.
CAUTION:
Never scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
b.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) (A) to the oil pan (lower) as shown in
the figure.
Use Genuine Liquid Gasket or equivalent.
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Install oil pan (lower).
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
4.
Install oil pan drain plug.
• Refer to the figure of components of former page for installa-
tion direction of drain plug washer. Refer to
.
5.
Install in the reverse order of removal after this step.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
Inspection
INFOID:0000000003802263
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leakage of engine oil.
M8
×
135 mm (5.31 in)
: 11
M8
×
92 mm (3.62 in)
: 5, 7, 8
M8
×
25 mm (0.98 in)
: Except the above
PBIC1636E
JPBIA0025ZZ
b
:
φ
4.0 - 5.0 mm (0.157 - 0.197 in)
JPBIA0026ZZ
PBIC0782E
OIL PAN AND OIL STRAINER
EM-43
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст