Nissan Teana J32. Instruction — part 1172

TM-212

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0703 STOP LAMP SWITCH

NO

>> Repair or replace the stop lamp switch. Refer to

BR-17, "Exploded View"

.

P0705 PARK/NEUTRAL POSITION SWITCH

TM-213

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0705 PARK/NEUTRAL POSITION SWITCH

Description

INFOID:0000000003806386

The PNP switch detects the selector lever position and sends a signal to the TCM.

DTC Logic

INFOID:0000000003806387

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Start engine.

4.

Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.

With GST

Follow the procedure “With CONSULT-III”.

Is “P0705 PNP SW/CIRC” detected?

YES

>> Go to

TM-213, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to

GI-35, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003806388

1.

CHECK POWER SOURCE

1.

Turn ignition switch OFF.

2.

Disconnect PNP switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between PNP switch vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>>

Check the following. If NG, repair or replace damaged parts.

• Harness for short or open between ignition switch and PNP switch
• 10 A fuse (No. 4, located in the fuse block J/B)

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0705

PNP SW/CIRC

TCM does not receive the cor-
rect voltage signal (based on
the gear position) from the
switch.

• Harness or connectors

(PNP switches circuit is open
or shorted.)

• PNP switch

VEHICLE SPEED

: More than 10 km/h (6 MPH)

ENG SPEED

: More than 450 rpm

ACC PEDAL OPEN

: More than 1.0/8

PNP switch vehicle side harness connector

Ground

Voltage (Approx.)

Connector

Terminal

Battery voltage

F57

3

TM-214

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0705 PARK/NEUTRAL POSITION SWITCH

• Ignition switch

2.

CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM vehicle side harness connector terminals and PNP switch vehicle side
harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 2)

Check continuity between TCM vehicle side harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK PNP SWITCH

1.

Remove control cable from instruction lever. Refer to

TM-319, "Exploded View"

.

2.

Check PNP switch. Refer to

TM-214, "Component Inspection (Park/Neutral Position Switch)"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

DETECT MALFUNCTIONING ITEM

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace TCM. Refer to

TM-315, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Component Inspection (Park/Neutral Position Switch)

INFOID:0000000003806389

1.

CHECK PNP SWITCH

Check continuity of PNP switch connector terminals.

TCM vehicle side harness connector

PNP switch vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

1

F57

5

Existed

2

6

3

7

4

8

11

4

TCM vehicle side harness connector

Ground

Continuity

Connector

Terminal

F23

1

Not existed

2

3

4

11

P0705 PARK/NEUTRAL POSITION SWITCH

TM-215

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace CVT assembly. Refer to

TM-332, "Exploded View"

.

PNP switch connector

Condition

Continuity

Connector

Terminal

F57

1

2

Instruction lever in “P” position

Existed

*

*Continuity should not exist in positions

other than the specified positions.

3

4

3

5

Instruction lever in “R” position

1

2

Instruction lever in “N” position

3

6

3

7

Instruction lever in “D” position

3

8

Instruction lever in “L” position