Nissan Teana J32. Instruction — part 274
BRC-154
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000003767308
Removal and Installation
INFOID:0000000003767299
REMOVAL
CAUTION:
• Before servicing, disconnect the battery cable from negative terminal.
• To remove brake tube, use a flare nut wrench to prevent flare nuts and brake tube from being dam-
aged. To install, use flare nut crowfoot and torque wrench.
• Do not apply excessive impact to ABS actuator and electric unit (control unit), such as dropping it.
• Do not remove and install actuator by holding harness.
• After work is completed, bleed air from brake tube. Refer to
BR-10, "Bleeding Brake System"
1.
Remove cowl top cover. Refer to
.
2.
Disconnect ABS actuator and electric unit (control unit) connector.
3.
Loosen brake tube flare nuts, then remove brake tubes from ABS actuator and electric unit (control unit).
4.
Remove ABS actuator and electric unit (control unit) bracket mounting nuts.
5.
Remove ABS actuator and electric unit (control unit) from vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Before servicing, disconnect the battery cable from negative terminal.
1.
ABS actuator and electric unit (control
unit)
2.
Bushing
3.
Bracket
A.
From master cylinder secondary side B.
From master cylinder primary side
C.
To front LH brake caliper
D.
To rear RH brake caliper
E.
To rear LH brake caliper
F.
To front RH brake caliper
: Vehicle front
Refer to GI section
for symbol marks in the figure.
JSFIA0223GB
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-155
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• To remove brake tube, use a flare nut wrench to prevent flare nuts and brake tube from being dam-
aged. To install, use flare nut crowfoot and torque wrench.
• Do not apply excessive impact to ABS actuator and electric unit (control unit), such as dropping it.
• Do not remove and install actuator by holding harness.
• After work is completed, bleed air from brake tube. Refer to
BR-10, "Bleeding Brake System"
• After installing harness connector in the ABS actuator and electric unit (control unit), make sure
connector is securely locked.
• When replacing ABS actuator and electric unit (control unit), make sure to adjust neutral position of
steering angle sensor. Refer to
BRC-66, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
Install ABS actuator and electric unit (control unit) as per the follow-
ing steps.
1.
Temporarily tighten mounting bolt (1) because the bracket (2) is
temporarily being hold.
2.
Tighten mounting bolt (3) while holding the bracket.
3.
Tighten mounting bolts to the specified torque in the order of (4),
(1).
JSFIA0271ZZ
BRC-156
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
YAW RATE/SIDE G SENSOR
YAW RATE/SIDE G SENSOR
Exploded View
INFOID:0000000003767352
Removal and Installation
INFOID:0000000003767353
REMOVAL
CAUTION:
Do not drop or strike yaw rate/side G sensor, or do not use power tool etc., because yaw rate/side G
sensor is sensitive to the impact.
1.
Remove center console. Refer to
2.
Remove rear ventilator duct. Refer to
VTL-54, "REAR VENTILATOR DUCT 2 : Exploded View"
.
3.
Disconnect yaw rate/side G sensor harness connector.
4.
Remove mounting nuts. Remove yaw rate/side G sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Do not drop or strike yaw rate/side G sensor, or do not use power tool etc., because yaw rate/side G
sensor is sensitive to the impact.
1.
Yaw rate/side G sensor
2.
Bracket
: Vehicle front
Refer to GI section
for symbol makes in the figure.
JSFIA0224GB
STEERING ANGLE SENSOR
BRC-157
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
STEERING ANGLE SENSOR
Exploded View
INFOID:0000000003767354
Removal and Installation
INFOID:0000000003767355
REMOVAL
1.
Remove spiral cable assembly. Refer to
2.
Remove steering angle sensor from spiral cable assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse steering angle sensor.
• When installing steering angle sensor, tighten it to the specified torque with an electric screwdriver.
Be sure to tighten it completely with no floating and tilting.
• After work, make sure to adjust neutral position of steering angle sensor. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Description"
1.
Steering angle sensor
: Vehicle front
Refer to GI section
for symbol marks in the figure.
JSFIA0237GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст