Nissan Teana J32. Instruction — part 616
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-35
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000003811089
Drive Shaft
INFOID:0000000003811090
VQ25DE
VQ35DE
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Item
Left side
Right side
Grease quantity
Wheel side
88 – 108 g (3.11 – 3.80 oz)
Transaxle side
153 – 166 g (5.40 – 5.85 oz)
Boots installed length
Wheel side
186.7 mm (7.35 in)
Transaxle side
153.4 mm (6.04 in)
Dimension of dynamic damper
207 – 213 mm (8.15 – 8.39 in)
Item
Left side
Right side
Grease quantity
Wheel side
170 – 190 g (6.00 – 6.70 oz)
Transaxle side
155 – 175 g (5.47 – 6.17 oz)
Boots installed length
Wheel side
158.6 mm (6.24 in)
Transaxle side
163.67 mm (6.44 in)
Dimension of dynamic damper
—
202 – 208 mm (7.95 – 8.19 in)
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
General Precautions . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
ON-VEHICLE MAINTENANCE . . . . . .
FUEL SYSTEM . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
Quick Connector . . . . . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . ..
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
FUEL TANK . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
FL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
General Precautions
INFOID:0000000003793245
WARNING:
When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
CAUTION:
• Use gasoline required by the regulations for octane number. Refer to
.
• Before removing fuel line parts, perform out the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
- Release fuel pressure from the fuel lines. Refer to
- Disconnect the battery cable from the negative terminal.
• Always replace O-ring and clamps with new ones.
• Never kink or twist tubes when they are being installed.
• Never tighten hose clamps excessively to avoid damaging hoses.
• After installing tubes, check there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check
for fuel leakage at connections.
- Start engine and rev it up and check for fuel leakage at connections.
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
“MI” may come on.
• For servicing “Evaporative Emission System” parts, refer to
.
PREPARATION
FL-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000003793247
Tool name
Description
Lock ring wrench
Removing and installing lock ring
ZZA0122D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст