Nissan Teana J32. Instruction — part 1030
SEC-108
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B210F PNP/CLUTCH INTERLOCK SWITCH
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> Repair or replace harness.
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E10
30
M123
140
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
30
Not existed
B2110 PNP/CLUTCH INTERLOCK SWITCH
SEC-109
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2110 PNP/CLUTCH INTERLOCK SWITCH
Description
INFOID:0000000003815062
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch
• Shift position signal from BCM (CAN)
DTC Logic
INFOID:0000000003815063
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON under the following conditions and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
SEC-109, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003815064
1.
CHECK BCM INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Turn ignition switch ON.
4.
Check voltage between BCM harness connector and ground.
Is the inspection normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PNP SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and BCM harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2110
INTER LOCK/PNP
SW
IPDM E/R detects the difference between the sig-
nals below for 1 second or more.
• PNP switch input signal
• Shift position signal from BCM (CAN)
• Harness or connectors
[Park/neutral position (PNP) switch
circuit is open or shorted
• Park/neutral position (PNP) switch
• IPDM E/R
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M123
140
Ground
Selector lever
P or N position
Battery voltage
Other than above
0
SEC-110
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B2110 PNP/CLUTCH INTERLOCK SWITCH
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> Repair or replace harness.
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E10
30
M123
140
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
30
Not existed
POWER SUPPLY AND GROUND CIRCUIT
SEC-111
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis Procedure
INFOID:0000000003910623
1.
CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Is the fuse fusing?
YES
>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connectors.
3.
Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
IPDM E/R
IPDM E/R : Diagnosis Procedure
INFOID:0000000003910624
1.
CHECK FUSES AND FUSIBLE LINK
Check that the following IPDM E/R fuses or fusible links are not blown.
Signal name
Fuse and fusible link No.
Battery power supply
I
10
Terminals
Voltage
(Approx.)
(+)
(
−
)
BCM
Ground
Connector
Terminal
M118
1
Battery voltage
M119
11
BCM
Ground
Continuity
Connector
Terminal
M119
13
Existed
Signal name
Fuses and fusible link No.
Battery power supply
E
50
51
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст