Nissan Teana J32. Instruction — part 1116
STR-14
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003860432
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
STARTER MOTOR
STR-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
ON-VEHICLE REPAIR
STARTER MOTOR
VQ25DE
VQ25DE : Exploded View
INFOID:0000000003860436
REMOVAL
DISASSEMBLY
1.
Converter housing
2.
“B” terminal harness
3.
Starter motor “B” terminal nut
4.
Starter motor “S” terminal nut
5.
Starter motor mounting bolt
6.
“S” terminal harness
7.
Starter motor
Refer to
JPBIA2371GB
STR-16
< ON-VEHICLE REPAIR >
STARTER MOTOR
Type: S114-936
VQ25DE : Removal and Installation
INFOID:0000000003860437
REMOVAL
1.
Remove the battery. Refer to
PG-109, "Removal and Installation"
.
2.
Remove the air cleaner assembly and air ducts.
3.
Disconnect the following unit connectors:
• ECM
• IPDM E/R
4.
Remove the battery tray.
5.
Remove the “B”terminal nut and “S” terminal nut.
6.
Remove the starter motor mounting bolts.
7.
Remove the starter motor upward from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
VQ25DE : Inspection
INFOID:0000000003860438
MAGNETIC SWITCH
• Before starting to check, disconnect the battery cable from the negative terminal.
JSAIA0936GB
1.
Magnetic switch assembly
2.
Adjusting plate
3.
Dust cover
4.
Shift lever set
5.
Pinion stopper clip
6.
Pinion stopper
7.
Pinion
8.
Pinion spring
9.
Gear case assembly
10. Center bracket (A)
11.
Yoke assembly
12. Armature assembly
13. Brush holder assembly
14. Thrust washer
15. Rear cover
16. Internal gear
17. Planetary gear
18. Pinion stopper
19. Packing
20. Thrust washer
21. Center bracket (P)
22. Thrust washer
23. E-ring
24. Clutch gear assembly
Refer to
for symbols not described on the above.
STARTER MOTOR
STR-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
• Disconnect “M” terminal of starter motor.
1.
Continuity test (between “S” terminal and switch body)
• Replace magnetic switch if continuity does not exist.
2.
Continuity test (between “S” terminal and “M” terminal)
• Replace magnetic switch if continuity does not exist.
PINION PROTRUSION LENGTH
• Compare movement “L” in height of pinion when it is pushed out
with magnetic switch energized and when it is pulled out by hand
until it touches stopper.
• If the measurement value is not in the specified area, adjust with
the adjusting plate.
PINION ASSEMBLY
A
: “S” terminal
B
: “B” terminal
C
: “M” terminal
SKIB9002E
A
: “S” terminal
B
: “B” terminal
C
: “M” terminal
SKIB9003E
Movement “L”
: Refer to SDS
SKIB0230E
JPBIA1984ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст