Nissan Teana J32. Instruction — part 963
REAR SUSPENSION ARM
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• Hook spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
• If swing torque exceeds the standard value, replace suspension
arm assembly.
Rotating Torque Inspection
• Attach the mounting nut to ball stud. Make sure that rotating torque
is within the specifications with a preload gauge (A) (SST:
ST3127S000).
- If rotating torque exceeds the standard value, replace suspension
arm assembly.
Axial End Play Inspection
• Move tip of ball stud in axial direction to check for looseness.
- If axial end play exceeds the standard value, replace suspension arm assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
(without VDC),
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-66, "ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
Standard
Swing torque
: Refer to
.
JPEIA0005ZZ
Standard
Rotating torque
: Refer to
PDIA1258E
Standard
Axial end play
: Refer to
.
RSU-18
< REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000003811160
Removal and Installation
INFOID:0000000003811161
REMOVAL
1.
Remove tires.
2.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-40, "BRAKE CALIPER ASSEMBLY : Exploded View"
3.
Remove wheel sensor and sensor harness. Refer to
BRC-58, "REAR WHEEL SENSOR : Exploded View"
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
4.
Remove center muffler and main muffler. Refer to
5.
Remove stabilizer bar. Refer to
6.
Separate the attachment between parking brake cable and vehicle and rear suspension member. Refer to
.
7.
Separate auto levelizer control unit harness connector (with xenon combination lamp type). Refer to
8.
Remove rear lower link and coil spring. Refer to
9.
Remove shock absorber (lower side). Refer to
10. Set suitable jack under rear suspension member.
11. Remove member stay (front and rear side).
12. Slowly lower jack, then remove rear suspension member, suspension arm, radius rod, front lower link and
axle housing from vehicle as a unit.
13. Remove the following parts.
• Axle housing: refer to
.
• Auto levelizer control unit (with xenon combination lamp type): refer to
• Suspension arm: refer to
.
• Radius rod: refer to
• Front lower link: refer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
1.
Member stay (rear side)
2.
Rear suspension member
3.
Member stay (front side)
Refer to
for symbols in the figure.
JPEIB0107GB
REAR SUSPENSION MEMBER
RSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
• After final tightening, install auto levelizer control unit (with xenon combination lamp type). Refer to
• Never reuse cotter pin.
Inspection
INFOID:0000000003811162
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
(without VDC),
BRC-152, "REAR WHEEL SENSOR : Exploded View"
(with VDC).
2.
Adjust parking brake operation (stroke).
PB-2, "Inspection and Adjustment"
3.
Check wheel alignment. Refer to
4.
Adjust neutral position of steering angle sensor. Refer to
BRC-66, "ADJUSTMENT OF STEERING
RSU-20
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000003811163
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000003811164
Wheel Height
INFOID:0000000003815380
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Item
Standard
Camber
Degree minute (Decimal degree)
Minimum
–0
°
57
′
(–0.95
°
)
Nominal
–0
°
27
′
(–0.45
°
)
Maximum
0
°
03
′
(0.05
°
)
Total toe-in
Distance
Minimum
0 mm (0 in)
Nominal
In 1.6 mm (0.063 in)
Maximum
In 3.2 mm (0.126 in)
Angle (left wheel or right wheel)
Degree minute (Decimal degree)
Minimum
0
°
00
′
(0.00
°
)
Nominal
In 0
°
04
′
(0.07
°
)
Maximum
In 0
°
08
′
(0.13
°
)
Item
Standard
Swing torque
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Measurement on spring balance (cotter pinhole position)
8.1 – 54.8 N (0.83 – 5.6 kg, 1.82 – 12.32 lb)
Rotating torque
0.5 – 3.4 N·m (0.06 – 0.34 kg-m, 5 – 30 in-lb)
Axial end play
0 mm (0 in)
Tire size
205/65R16
215/55R17
Engine
VQ25DE
VQ35DE
Grade
250XE
250XL-V6
250XV-V6
350XV-V6
Front (Hf)
712 mm (28.03 in)
711 mm (27.99 in)
710 mm (27.95 in)
Rear (Hr)
703 mm (27.68 in)
702 mm (27.64 in)
701 mm (27.60 in)
SFA818A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст