Nissan Teana J32. Instruction — part 1059
CRASH ZONE SENSOR
SR-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
3.
Disconnect crash zone sensor harness connector (A).
4.
Remove the crash zone sensor (1) fixing nuts (B), and then
remove crash zone sensor.
CAUTION:
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use old fixing nuts after removal; replace with new nuts.
• In the case that a malfunction is detected by the air bag warning lamp, after repair or replacement of
the malfunctioning parts, reset the memory by self-diagnosis or by CONSULT-III.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-10, "Diagnosis Description"
JMHIA0625ZZ
JMHIA0009ZZ
SR-20
< ON-VEHICLE REPAIR >
SIDE AIR BAG (SATELLITE) SENSOR
SIDE AIR BAG (SATELLITE) SENSOR
Exploded View
INFOID:0000000003838675
Removal and Installation
INFOID:0000000003838676
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove the pre-tensioner seat belt retractor. Refer to
SB-5, "SEAT BELT RETRACTOR : Removal and
.
2.
Remove the side air bag (satellite) sensor (1) fixing nuts (B).
3.
Disconnect side air bag (satellite) sensor harness connector (A),
and then remove side air bag (satellite) sensor.
CAUTION:
1.
Side air bag (satellite) sensor
: Vehicle front
Refer to
for symbols in the figure.
JMHIA0626GB
JMHIA0627ZZ
SIDE AIR BAG (SATELLITE) SENSOR
SR-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Never impact he side air bag (satellite) sensor.
• Replace the side air bag (satellite) sensor if it has been
dropped or sustained an impact.
• Replace the side air bag (satellite) sensor of deployed SRS front side air bag and deployed SRS side
curtain air bag.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never use old fixing nuts after removal; replace with new nuts.
• In the case that a malfunction is detected by the air bag warning lamp, after repair or replacement of
the malfunctioning parts, reset the memory by self-diagnosis or by CONSULT-III.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-10, "Diagnosis Description"
JMHIA0009ZZ
SR-22
< ON-VEHICLE REPAIR >
DIAGNOSIS SENSOR UNIT
DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000003838677
Removal and Installation
INFOID:0000000003838678
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Before disconnecting the diagnosis sensor unit harness connector, be sure to disconnect each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Disconnect each connector of all air bag modules and pre-tensioner seat belts.
2.
Remove the center console assembly. Refer to
IP-22, "Removal and Installation"
3.
Remove the rear ventilator duct. Refer to
VTL-53, "REAR VENTILATOR DUCT 1 : Exploded View"
.
1.
Bracket
2.
Diagnosis sensor unit
: Vehicle front
Refer to
for symbols in the figure.
JMHIA0628GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст