Nissan Teana J32. Instruction — part 1279
HEADLAMP WASHER PUMP
WW-101
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
HEADLAMP WASHER PUMP
Exploded View
INFOID:0000000003761629
Removal and Installation
INFOID:0000000003761630
REMOVAL
1.
Remove the fender protector RH (front). Refer to
EXT-22, "FENDER PROTECTOR : Exploded View"
.
2.
Disconnect the headlamp washer pump connector.
3.
Disconnect the headlamp washer tube.
4.
Remove the headlamp washer pump from the washer tank.
5.
Remove the packing from the washer tank.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never twist the packing when installing the headlamp washer pump.
1.
Washer tank
2.
Packing
3.
Clip
4.
Headlamp washer tube
5.
Headlamp washer pump
6.
Headlamp washer pump connector
JPLIA1136ZZ
WW-102
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
FRONT WASHER NOZZLE AND TUBE
Hydraulic Layout
INFOID:0000000003761632
Removal and Installation
INFOID:0000000003761633
REMOVAL
1.
Open the hood.
2.
Remove the washer nozzle in numerical order shown in the fig-
ure.
3.
Disconnect the washer tube from the washer nozzle.
INSTALLATION
1.
Connect the washer tube into the washer nozzle.
2.
Fix the pawl-side behind the washer nozzle first, then push the resin clip-side.
3.
Adjust the washer nozzle spray position. Refer to
WW-102, "Inspection and Adjustment"
.
CAUTION:
The spray positions differ. Check that left and right nozzles are installed correctly.
Inspection and Adjustment
INFOID:0000000003761634
INSPECTION
Washer Nozzle Inspection
1.
Washer nozzle
2.
Washer tube
3.
Washer tank
: Clip
JPLIA1137ZZ
: Vehicle front
JPLIA1138ZZ
FRONT WASHER NOZZLE AND TUBE
WW-103
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in)
JPLIA1139ZZ
1.
End of cowl top cover
: Spray area
: Target spray position
Spray position
H (Height)
L (Width)
Spray area
A
293.2 (11.54)
490.7 (19.32)
φ
80 (3.15)
B
422.0 (16.61)
298.6 (11.76)
φ
80 (3.15)
C
376.2 (14.81)
121.5 (4.78)
φ
80 (3.15)
D
327.9 (12.91)
56.3 (2.22)
φ
80 (3.15)
E
383.1 (15.08)
300 (11.81)
φ
80 (3.15)
F
305.7 (12.04)
475.1 (18.70)
φ
80 (3.15)
JPLIA1140ZZ
WW-104
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
JPLIA1141ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст