Nissan Teana J32. Instruction — part 483
EM-56
< ON-VEHICLE REPAIR >
TIMING CHAIN
16. Remove internal chain guide, tension guide and slack guide.
NOTE:
Tension guide can be removed after removing timing chain (pri-
mary).
17. Remove timing chain (primary) and crankshaft sprocket.
CAUTION:
After removing timing chain (primary), never turn crankshaft and camshaft separately, or valves
will strike the piston heads.
18. Remove timing chain (secondary) and camshaft sprockets as follows:
a.
Attach a suitable stopper pin (B) to the bank 1 (A) and bank 2
(C) timing chain tensioners (secondary) (1).
NOTE:
• Use approximately 0.5 mm (0.02 in) dia. hard metal pin as a
stopper pin.
• For removal of timing chain tensioner (secondary), refer to
. [Removing camshaft bracket (No. 1)
is required.]
b.
Remove camshaft sprockets (INT and EXH) mounting bolts.
• Secure the hexagonal portion of camshaft using a wrench to
loosen mounting bolts.
CAUTION:
Never loosen mounting bolts with securing anything
other than the camshaft hexagonal portion or with ten-
sioning the timing chain.
c.
Remove timing chain (secondary) together with camshaft sprockets.
• Turn camshaft slightly to secure slackness of timing chain on timing chain tensioner (secondary) side.
PBIC2266E
JPBIA1727ZZ
KBIA1698J
TIMING CHAIN
EM-57
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Insert 0.5 mm (0.020 in) thick metal or resin plate between tim-
ing chain and timing chain tensioner plunger (guide) (F).
Remove timing chain (secondary) (1) together with camshaft
sprockets with timing chain loose from guide groove.
CAUTION:
Be careful of plunger coming-off when removing timing chain (secondary). This is because
plunger of timing chain tensioner (secondary) moves during operation, leading to coming-off of
fixed stopper pin.
NOTE:
• Camshaft sprocket (INT) is two-for-one structure of sprockets for timing chain (primary) and for timing
chain (secondary).
• Figure is shown as an example of bank 1.
• When handling camshaft sprocket (INT), be careful of the following caution:
CAUTION:
• Handle carefully to avoid any shock to camshaft sprocket.
• Never disassemble. [Never loosen bolts (A) as shown in
the figure].
19. Remove timing chain tensioners (secondary) from cylinder head as follows, if necessary.
• Remove timing chain tensioners (secondary) with a stopper pin attached.
20. Use a scraper to remove all traces of old liquid gasket from front
timing chain case, and opposite mating surfaces.
• Remove old liquid gasket from bolt hole (B) and thread.
A
: Bank 1
B
: Timing chain tensioner (Body)
C
: View C
D
: Stopper pin
E
: Plate
JPBIA1725ZZ
PBIC2980E
SEM737G
A
: Remove sticking old liquid gasket
JPBIA0051ZZ
EM-58
< ON-VEHICLE REPAIR >
TIMING CHAIN
21. Use a scraper to remove all traces of old liquid gasket from
water pump cover.
INSTALLATION
NOTE:
The below figure shows the relationship between the mating mark on each timing chain and that on the corre-
sponding sprocket, with the components installed.
1.
Install timing chain tensioners (secondary) to cylinder head as follows if removed. Refer to
• Install timing chain tensioners (secondary) with a stopper pin attached and new O-ring.
SEM926E
1.
Internal chain guide
2.
Camshaft sprocket (INT)
3.
Timing chain (secondary)
4.
Camshaft sprocket (EXH)
5.
Timing chain tensioner (primary)
6.
Slack guide
7.
Timing chain (primary)
8.
Crankshaft sprocket
9.
Water pump
10. Tension guide
11.
Timing chain tensioner (secondary)
12. Crankshaft key
A.
Mating mark
B.
Mating mark (pink link)
C.
Mating mark (punched)
D.
Mating mark (orange)
E.
Mating mark (notched)
JPBIA1716GB
TIMING CHAIN
EM-59
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Check that dowel pin hole, dowel pin and crankshaft key are
located as shown in the figure. (No. 1 cylinder at compression
TDC)
NOTE:
Though camshaft does not stop at the position as shown in the
figure, for the placement of cam nose, it is generally accepted
camshaft is placed for the same direction of the figure.
CAUTION:
Hole on small dia. side must be used for intake side dowel pin hole. Never misidentify (ignore big
dia. side).
3.
Install timing chain (secondary) and camshaft sprockets (INT and EXH) as follows:
CAUTION:
Mating marks between timing chain and sprockets slip easily. Confirm all mating mark positions
repeatedly during the installation process.
a.
Push plunger of timing chain tensioner (secondary) and keep it
pressed in with stopper pin (A).
b.
Install timing chain (secondary) (1) and camshaft sprockets (INT
and EXH).
NOTE:
Figure shows bank 1 (rear view).
• Align the mating marks on timing chain (secondary) (orange
link) with the ones on camshaft sprockets (INT and EXH)
(punched), and install them.
NOTE:
• Mating marks for camshaft sprocket (INT) are on the back
side of camshaft sprocket (secondary).
• There are two types of mating mark, circle and oval types.
They should be used for the bank 1 and bank 2, respectively.
Camshaft dowel pin hole (intake side)
: At cylinder head upper face side in each bank
Camshaft dowel pin (exhaust side)
: At cylinder head upper face side in each bank
Crankshaft key
: At cylinder head side of bank 1
KBIA1073E
JPBIA0095ZZ
A
: Camshaft sprocket (INT) back face
B
: Orange link
C
: Mating mark (Circle)
D
: Camshaft sprocket (EXH) back face
E
: Mating mark (2 circle on front face)
F
: Dowel pin groove
G
: Mating mark (2 ovals on front face)
H
: Mating mark (Oval)
I
: Dowel pin hole
JPBIA1726ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст