Nissan Teana J32. Instruction — part 552
EXL-178
< ON-VEHICLE MAINTENANCE >
[XENON TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000003773617
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000003773618
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Illuminate the front fog lamp.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4.
Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
A: UP
B: DOWN
JPLIA1086ZZ
JPLIA0008ZZ
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-179
< ON-VEHICLE MAINTENANCE >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
EXL-180
< ON-VEHICLE REPAIR >
[XENON TYPE]
FRONT COMBINATION LAMP
ON-VEHICLE REPAIR
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000003773619
REMOVAL
DISASSEMBLY
1.
Front combination lamp
JPLIA1087ZZ
1.
Front turn signal lamp bulb
2.
Front turn signal lamp bulb socket
3.
Halogen bulb (HI)
4.
Seal packing
5.
Resin cap
6.
Ground line
7.
Xenon bulb socket (Starter)
8.
Xenon bulb (LO)
9.
Seal packing
10.
HID control unit (Inverter)
11. Parking lamp bulb socket
12. Parking lamp bulb
13.
Headlamp housing assembly
14. Retaining spring
JPLIA1088ZZ
FRONT COMBINATION LAMP
EXL-181
< ON-VEHICLE REPAIR >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000003773620
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the front bumper fascia. Refer to
2.
Remove the headlamp mounting bolts.
3.
Remove the harness clips from the headlamp housing.
4.
Pull out the headlamp assembly forward the vehicle.
5.
Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
.
Replacement
INFOID:0000000003773621
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1.
Remove the fender protector. Keep a service area. Refer to
EXT-22, "FENDER PROTECTOR : Exploded
.
2.
Rotate the resin cap counterclockwise and unlock it.
3.
Disconnect the bulb socket ground line.
4.
Rotate the bulb socket counterclockwise and unlock it.
5.
Unlock the retaining spring. And then remove the bulb from the
headlamp housing.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
HEADLAMP BULB (HI)
1.
Remove the fender protector. Keep a service area. Refer to
EXT-22, "FENDER PROTECTOR : Exploded
.
2.
Disconnect the headlamp (HI) connector.
3.
Rotate the bulb counterclockwise and unlock it.
4.
Remove the bulb from the headlamp housing.
PARKING LAMP BULB
1.
Remove the fender protector. Keep a service area. Refer to
EXT-22, "FENDER PROTECTOR : Exploded
.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the parking lamp bulb socket.
FRONT TURN SIGNAL LAMP BULB
JPLIA1089ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст