Nissan Teana J32. Instruction — part 1070
SRC-34
< COMPONENT DIAGNOSIS >
B1050 DRIVER AIRBAG MODULE
B1050 DRIVER AIRBAG MODULE
Description
INFOID:0000000003813960
For driver air bag module, crash is judged by main “G” sensor output signal and safing algorithm in front direc-
tion.
OPERATION
In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This
generates hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Driver air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Driver air bag module is installed on the center of steering wheel with fixed bolts.
DTC Logic
INFOID:0000000003813961
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-10, "Air Bag Warning Lamp Diagnosis"
.
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003813962
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1050
DRIVER AIRBAG MOD-
ULE
[VB-SHORT]
Driver air bag module circuit is shorted
to some power supply circuit
(including the spiral cable)
• Disconnection of wiring harness and
short
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sen-
sor unit
B1050 DRIVER AIRBAG MODULE
SRC-35
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> Replace wiring harness.
3.
CHECK SPIRAL CABLE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and Combination switch (Spiral cable) harness con-
nector.
3.
Check continuity between driver side air bag module harness connector and body side harness connec-
tor.
4.
Check continuity between driver air bag module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace spiral cable. Refer to
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Driver air bag module
Combination switch (Spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
M350
10
M32
28
Existed
11
30
Driver air bag module
Ground
Continuity
Connector
Terminal
M350
10
Not existed
11
SRC-36
< COMPONENT DIAGNOSIS >
B1051 DRIVER AIRBAG MODULE
B1051 DRIVER AIRBAG MODULE
Description
INFOID:0000000003813963
For driver air bag module, crash is judged by main “G” sensor output signal and safing algorithm in front direc-
tion.
OPERATION
In case of frontal collision whose acceleration exceeds the specified level, the ignition materials are ignited by
electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This
generates hot gases that flow into the air bag through a filter and expand the bag.
STRUCTURE
Driver air bag module mainly consists of air bag and inflator which inflates air bag.
INSTALLATION
Driver air bag module is installed on the center of steering wheel with fixed bolts.
DTC Logic
INFOID:0000000003813964
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-10, "Air Bag Warning Lamp Diagnosis"
.
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003813965
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1051
DRIVER AIRBAG MOD-
ULE
[GND-SHORT]
Driver air bag module circuit is shorted
to ground
(including the spiral cable)
• Disconnection of wiring harness and
short
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sen-
sor unit
B1051 DRIVER AIRBAG MODULE
SRC-37
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> Replace wiring harness.
3.
CHECK SPIRAL CABLE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver air bag module harness connector and Combination switch (Spiral cable) harness con-
nector.
3.
Check continuity between driver side air bag module harness connector and body side harness connec-
tor.
4.
Check continuity between driver air bag module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace spiral cable. Refer to
4.
REPLACE DRIVER AIR BAG MODULE
1.
Replace driver air bag module. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Driver air bag module
Combination switch (Spiral cable)
Continuity
Connector
Terminal
Connector
Terminal
M350
10
M32
28
Existed
11
30
Driver air bag module
Ground
Continuity
Connector
Terminal
M350
10
Not existed
11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст