Nissan Teana J32. Instruction — part 455
EC-358
< ECU DIAGNOSIS >
[VQ25DE, VQ35DE]
ECM
TP SEN 1-B1
• Ignition switch: ON
(Engine stopped)
• Selector lever: D
Accelerator pedal: Fully released
More than 0.36 V
Accelerator pedal: Fully depressed
Less than 4.75 V
TP SEN 2-B1*
1
• Ignition switch: ON
(Engine stopped)
• Selector lever: D
Accelerator pedal: Fully released
More than 0.36 V
Accelerator pedal: Fully depressed
Less than 4.75 V
INT/A TEMP SE
• Ignition switch: ON
Indicates intake air tempera-
ture
START SIGNAL
• Ignition switch: ON
→
START
→
ON
OFF
→
ON
→
OFF
CLSD THL POS
• Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
ON
Accelerator pedal: Slightly depressed
OFF
AIR COND SIG
• Engine: After warming up, idle the
engine
Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates.)
ON
P/N POSI SW
• Ignition switch: ON
Selector lever: P or N
ON
Selector lever: Except above
OFF
PW/ST SIGNAL
• Engine: After warming up, idle the
engine
Steering wheel: Not being turned
OFF
Steering wheel: Being turned
ON
LOAD SIGNAL
• Ignition switch: ON
Rear window defogger switch: ON
and/or
Lighting switch: 2nd position
ON
Rear window defogger switch and lighting
switch: OFF
OFF
IGNITION SW
• Ignition switch: ON
→
OFF
→
ON
ON
→
OFF
→
ON
HEATER FAN SW
• Engine: After warming up, idle the
engine
Heater fan switch: ON
ON
Heater fan switch: OFF
OFF
BRAKE SW
• Ignition switch: ON
Brake pedal: Fully released
OFF
Brake pedal: Slightly depressed
ON
INJ PULSE-B1
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
2.0 - 3.0 msec
2,000 rpm
1.9 - 2.9 msec
INJ PULSE-B2
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
2.0 - 3.0 msec
2,000 rpm
1.9 - 2.9 msec
IGN TIMING
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
7
°
- 17
°
BTDC
2,000 rpm
25
°
- 45
°
BTDC
CAL/LD VALUE
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
5% - 35%
2,500 rpm
5% - 35%
MASS AIRFLOW
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
2.0 - 6.0 g·m/s
2,500 rpm
7.0 - 20.0 g·m/s
PURG VOL C/V
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.)
0%
2,000 rpm
—
Monitor Item
Condition
Values/Status
ECM
EC-359
< ECU DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
INT/V TIM (B1)
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
−
5
°
- 5
°
CA
2,000 rpm
Approx. 0
°
- 30
°
CA
INT/V TIM (B2)
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
−
5
°
- 5
°
CA
2,000 rpm
Approx. 0
°
- 30
°
CA
INT/V SOL (B1)
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
0% - 2%
2,000 rpm
Approx. 0% - 50%
INT/V SOL (B2)
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Idle
0% - 2%
2,000 rpm
Approx. 0% - 50%
VIAS S/V-1
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
When revving engine up to 5,000 rpm
quickly
OFF
→
ON
→
OFF
VIAS S/V-2
• Engine: After warming up
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
When revving engine up to 5,000 rpm
quickly
OFF
→
ON
→
OFF
AIR COND RLY
• Engine: After warming up, idle the
engine
Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates)
ON
ENGINE MOUNT
• Engine: After warming up
Below 950 rpm
IDLE
Above 950 rpm
TRVL
FUEL PUMP RLY
• For 1 second after turning ignition switch: ON
• Engine running or cranking
ON
• Except above
OFF
THRTL RELAY
• Ignition switch: ON
ON
COOLING FAN
• Engine: After warming up, idle the
engine
• Air conditioner switch: OFF
Engine coolant temperature: 97
°
C
(206
°
F) or less
OFF
Engine coolant temperature: Between
98
°
C (208
°
F) and 99
°
C (210
°
F)
LOW
Engine coolant temperature: Between
100
°
C (212
°
F) and 104
°
C (219
°
F)
MID
Engine coolant temperature: 105
°
C
(221
°
F) or more
HI
HO2S2 HTR (B1)
• Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
ON
• Engine speed: Above 3,600 rpm
OFF
HO2S2 HTR (B2)
• Engine speed: Below 3,600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
ON
• Engine speed: Above 3,600 rpm
OFF
I/P PULLY SPD
• Vehicle speed: More than 20km/h (12 MPH)
Almost the same speed as
the tachometer indication
VEHICLE SPEED
• Turn drive wheels and compare CONSULT-III value with the speedometer in-
dication.
Almost the same speed as
the speedometer indication
Monitor Item
Condition
Values/Status
EC-360
< ECU DIAGNOSIS >
[VQ25DE, VQ35DE]
ECM
IDL A/V LEARN
• Engine: Running
Idle air volume learning has not been per-
formed yet.
YET
Idle air volume learning has already been
performed successfully.
CMPLT
ENG OIL TEMP
• Engine: After warming up
More than 70
°
C (158
°
F)
TRVL AFTER MIL
• Ignition switch: ON
Vehicle has traveled after MI has illumi-
nated.
0 - 65,535 km
(0 - 40,723 miles)
A/F S1 HTR (B1)
• Engine: After warming up, idle the engine
(More than 140 seconds after starting engine)
4 - 100%
A/F S1 HTR (B2)
• Engine: After warming up, idle the engine
(More than 140 seconds after starting engine)
4 - 100%
AC PRESS SEN
• Engine: Idle
• Both A/C switch and blower fan switch: ON (Compressor operates)
1.0 - 4.0 V
VHCL SPEED SE
• Turn drive wheels and compare CONSULT-III value with the speedometer in-
dication.
Almost the same speed as
the speedometer indication
SET VHCL SPD
• Engine: Running
ASCD: Operating
The preset vehicle speed is
displayed
MAIN SW
• Ignition switch: ON
MAIN switch: Pressed
ON
MAIN switch: Released
OFF
CANCEL SW
• Ignition switch: ON
CANCEL switch: Pressed
ON
CANCEL switch: Released
OFF
RESUME/ACC SW
• Ignition switch: ON
RESUME/ACCELERATE switch:
Pressed
ON
RESUME/ACCELERATE switch: Re-
leased
OFF
SET SW
• Ignition switch: ON
SET/COAST switch: Pressed
ON
SET/COAST switch: Released
OFF
BRAKE SW1
(ASCD brake switch)
• Ignition switch: ON
Brake pedal: Fully released
ON
Brake pedal: Slightly depressed
OFF
BRAKE SW2
(Stop lamp switch)
• Ignition switch: ON
Brake pedal: Fully released
OFF
Brake pedal: Slightly depressed
ON
VHCL SPD CUT
• Ignition switch: ON
NON
LO SPEED CUT
• Ignition switch: ON
NON
AT OD MONITOR
• Ignition switch: ON
OFF
AT OD CANCEL
• Ignition switch: ON
OFF
CRUISE LAMP
• Ignition switch: ON
MAIN switch: Pressed at the 1st time
→
at the 2nd time
ON
→
OFF
SET LAMP
• MAIN switch: ON
• When vehicle speed is between
40 km/h (25 MPH) and 144 km/h
(89 MPH)
ASCD: Operating
ON
ASCD: Not operating
OFF
ALT DUTY
• Engine: Idle
0 - 80%
A/F ADJ-B1
• Engine: Running
−
0.330 - 0.330
A/F ADJ-B2
• Engine: Running
−
0.330 - 0.330
BAT CUR SEN
• Engine speed: Idle
• Battery: Fully charged*
2
• Selector lever: P or N
• Air conditioner switch: OFF
• No load
Approx. 2,600 - 3,500 mV
Monitor Item
Condition
Values/Status
ECM
EC-361
< ECU DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
*1: Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, they differ
from ECM terminals voltage signal.
*2: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
• ECM is located in the engine room left side near battery. For this inspection, remove passenger side instru-
ment lower panel.
• Specification data are reference values.
• Pulse signal is measured by CONSULT-III.
ALT DUTY SIG
• Power generation voltage variable control: Operating
ON
• Power generation voltage variable control: Not operating
OFF
Monitor Item
Condition
Values/Status
PBIA9221J
Terminal No.
Description
Condition
Value
(Approx.)
+
-–
Signal name
Input/
Output
1
(P/B)
112
(B)
Fuel injector No. 6
Output
[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle
BATTERY VOLTAGE
(11 - 14 V)
3
(L/W)
Fuel injector No. 5
29
(LG/R)
Fuel injector No. 4
30
(R/Y)
Fuel injector No. 3
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm
BATTERY VOLTAGE
(11 - 14 V)
31
(R/W)
Fuel injector No. 2
32
(R/B)
Fuel injector No. 1
2
(G/W)
112
(B)
Throttle control motor relay
power supply
Input
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
4
(BR/Y)
112
(B)
A/F sensor 1 heater
(Bank 1)
Output
[Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after
starting engine)
2.9 - 8.8 V
JMBIA0047GB
JMBIA0048GB
JMBIA0902GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст