Nissan Teana J32. Instruction — part 1002
REAR SEAT
SE-141
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Seat harness
2.
Cup holder
3.
Bushing
4.
Armrest bracket
5.
Armrest assembly
6.
Seat heater switch RH
7.
Air conditioning switch RH
8.
Rear sunshade switch
9.
Air conditioning switch LH
10. Seat heater switch LH
11.
Rear audio switch
12. Ventilation motor (seat cushion)
13. Blower filter
14. Seat cushion duct A
15. Seat cushion duct B
16. Seat cushion hook
17. Seat cushion pad
18. Seat cushion trim
JMJIA1883GB
SE-142
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
REAR SEAT
Removal and Installation
INFOID:0000000003840027
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the headrest.
2.
Remove the seat cushion.
• Pull the lock lever (1) at the front bottom of the seat cushion
forward (1 for each side), and pull the seat cushion upward to
release the wire (2) from the seat cushion hook. Then pull the
seat cushion forward to remove.
• Remove the seat cushion from the vehicle.
3.
Remove the seatback.
• Remove the bolts under seatback.
• Lift up seatback from underneath, and then remove seatback from seatback hook that is fixed to the
vehicle.
• Remove the seatback from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
Disassembly and Assembly
INFOID:0000000003840028
SEATBACK
Disassembly
1.
Remove armrest assembly.
• Remove the pawls, and pull out the cup holder.
19. Seatback center pad
20. Seat cushion heater unit
21. Seatback heater unit
22. Seatback pad
23. Seatback trim
24. Seat belt hook
25. Headrest holder (locked)
26. Headrest holder (free)
27. Headrest side (long type)
28. Headrest side (normal type)
29. Headrest center (normal type)
30. Headrest center (long type)
31. Seatback duct C
32. Seatback duct B
33. Ventilation motor (seatback)
34. Blower filter
35. Seatback duct A
36. Ventilation seat control unit
Refer to
for symbols in the figure.
JMJIA0251ZZ
: Pawl
JMJIA1936ZZ
REAR SEAT
SE-143
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the bolts (A), and then remove armrest retainer.
• Remove the armrest assembly.
2.
Remove the seatback trim.
• Remove the screws, and then seat belt hook.
• Remove the headrest holder.
CAUTION:
Before installing headrest holder, check its orientation
(front/rear and right/left).
• Remove the hog rings to separate the seatback trim and seatback pad.
Assembly
Assemble in the reverse order of disassembly.
SEAT CUSHION
Disassembly
Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
Assembly
Assemble in the reverse order of disassembly.
JMJIA1939ZZ
PIIB4084J
SE-144
< ON-VEHICLE REPAIR >
[WITHOUT VENTILATION SEAT]
POWER SEAT SWITCH
POWER SEAT SWITCH
Exploded View
INFOID:0000000003885027
.
Removal and Installation
INFOID:0000000003885028
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the seat cushion outer finisher (1). Refer to
SE-135, "Removal and Installation"
2.
Remove switch knob.
3.
Remove screws (A).
4.
Remove the power seat switch (2) from the seat cushion outer
finisher.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to clump the harness to the right place.
JMJIA1952ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст