Nissan Teana J32. Instruction — part 352
HOOD
DLK-191
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ON-VEHICLE REPAIR
HOOD
HOOD ASSEMBLY
HOOD ASSEMBLY : Exploded View
INFOID:0000000003813383
REMOVAL
ADJUSTMENT
1.
Hood insulator
2.
Hood hinge (RH/LH)
3.
Hood seal (front) (RH/LH)
4.
Radiator core seal
5.
Grommet
6.
Hood support rod
7.
Clamp
8.
Hood assembly
9.
Hood bumper rubber (lower) (RH/
LH)
10. Hood bumper rubber (side) (RH/LH)
Refer to
JMKIA2380ZZ
DLK-192
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000003813384
CAUTION:
Operate with two workers, because of its heavy weight.
REMOVAL
1.
Remove hood insulator.
2.
Remove washer nozzle and washer tube. Refer to
WW-102, "Removal and Installation"
3.
Support hood assembly with a proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the hood open when removing the hood
stay.
4.
Remove hood hinge mounting nuts on the hood to remove the hood assembly.
5.
Remove the following parts after removing the hood assembly.
• Radiator core seal
• Hood bumper rubber (lower, side)
• Hood seal (front)
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood lock assembly
4.
Hood hinge
5.
Front bumper fascia
6.
Front combination lamp
7.
Front fender
Refer to
for symbols in the figure.
JMKIA2391GB
HOOD
DLK-193
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Front grille: Refer to
EXT-18, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installing, perform hood fitting adjustment. Refer to
DLK-193, "HOOD ASSEMBLY : Adjust-
• After installing, perform front washer nozzle and tube inspection and adjustment. Refer to
.
HOOD ASSEMBLY : Adjustment
INFOID:0000000003813385
Check the clearance and the surface height between hood and each part visually and by touching. (Fitting
standard dimension in the table below should be satisfied.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Remove hood lock and adjust the height by rotating hood bumper rubber (side, lower) until hood becomes
1 to1.5 mm (0.039 to 0.059 in) lower than fender.
2.
Temporarily tighten hood lock assembly, and position by engaging it with hood striker. Check hood lock
and striker for looseness and adjust the clearance and evenness with striker to satisfy the specification.
3.
Adjust A and B shown in the figure to the following value with hood's own weight by dropping it from
approximately 200 mm (7.874 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5 lb)].
4.
After adjustment, tighten lock bolts to the specified torque.
HOOD HINGE
Portion
Standard
Difference
(RH/LH, MAX)
Hood – Front bumper
fascia
A – A
D
Clearance
3.7 – 8.3
(0.146 – 0.315)
2.0
(0.079)
Hood – Front combina-
tion lamp
B – B
E
Clearance
2.4 – 6.8
(0.094 – 0.268)
2.5
(0.098)
Hood – Front fender
C – C
F
Clearance
3.1 – 6.1
(0.122 – 0.240)
2.0
(0.079)
G
Surface height
−
1.5 – 1.5
(
−
0.059 – 0.059)
—
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A
: 20.0 mm (0.787 in)
B
: 6.8 mm (0.268 in)
JMKIA2399ZZ
DLK-194
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
HOOD HINGE : Exploded View
INFOID:0000000003819555
HOOD HINGE : Removal and Installation
INFOID:0000000003813387
REMOVAL
1.
Remove hood assembly. Refer to
DLK-192, "HOOD ASSEMBLY : Removal and Installation"
2.
Remove front fender. Refer to
DLK-199, "Removal and Installation"
3.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
• After installation, perform hood fitting adjustment. Refer to
DLK-193, "HOOD ASSEMBLY : Adjust-
HOOD SUPPORT ROD
1.
Hood insulator
2.
Hood hinge (RH/LH)
3.
Hood seal (front) (RH/LH)
4.
Radiator core seal
5.
Grommet
6.
Hood support rod
7.
Clamp
8.
Hood assembly
9.
Hood bumper rubber (lower) (RH/
LH)
10.
Hood bumper rubber (side) (RH/LH)
for symbols in the figure.
JMKIA2380ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст