Nissan Teana J32. Instruction — part 824
MWI
B2205 VEHICLE SPEED
MWI-39
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2205 VEHICLE SPEED
Description
INFOID:0000000003792558
Vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) via CAN communication
to combination meter.
DTC Logic
INFOID:0000000003792559
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000003792560
1.
PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Perform “Self Diagnostic Result” of ABS actuator and electric unit (control unit), and repair or replace malfunc-
tioning parts.
>> Refer to
BRC-13, "CONSULT-III Function"
(with ABS models) or
(with VDC models).
DTC
Display contents of
CONSULT-III
Diagnostic item is detected when ...
Probable malfunction location
B2205
VEHICLE SPEED
An abnormal vehicle speed signal is input
from ABS actuator and electric unit (control
unit) for 2 seconds or more
• Wheel sensor
• ABS actuator and electric unit (control unit)
MWI-40
< COMPONENT DIAGNOSIS >
B2267 ENGINE SPEED
B2267 ENGINE SPEED
Description
INFOID:0000000003792561
The engine speed signal is transmitted from ECM to the combination meter via CAN communication.
DTC Logic
INFOID:0000000003792562
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000003792563
1.
PERFORM SELF-DIAGNOSIS OF ECM
Perform “Self Diagnostic Result” of ECM, and repair or replace malfunctioning parts.
>> Refer to
EC-113, "CONSULT-III Function"
.
DTC
Display contents of
CONSULT-III
Diagnostic item is detected when ...
Probable malfunction location
B2267
ENGINE SPEED
ECM continuously transmits abnormal engine
speed signals for 2 seconds or more
• Crankshaft position sensor (POS)
• ECM
MWI
B2268 WATER TEMP
MWI-41
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2268 WATER TEMP
Description
INFOID:0000000003792564
The engine coolant temperature signal is transmitted from ECM to the combination meter via CAN communi-
cation.
DTC Logic
INFOID:0000000003792565
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000003792566
1.
PERFORM SELF-DIAGNOSIS OF ECM
Perform “Self Diagnosis Result” of ECM, and repair or replace malfunctioning parts.
>> Refer to
EC-113, "CONSULT-III Function"
.
DTC
Display contents of
CONSULT-III
Diagnostic item is detected when ...
Probable malfunction location
B2268
WATER TEMP
ECM continuously transmits abnormal engine
coolant temperature signals for 60 seconds or
more
• Engine coolant temperature sensor
• ECM
MWI-42
< COMPONENT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
INFOID:0000000003792567
1.
CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check harness between combination meter and fuse.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Check continuity between combination meter harness connector terminals and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure
INFOID:0000000003900505
1.
CHECK FUSE AND FUSIBLE LINK
Check that the following fuse and fusible link are not blown.
Power source
Fuse No.
Battery
11
Ignition switch ON or START
4
Terminals
Voltage
(Approx.)
(+)
(-)
Combination meter
Ground
Connector
Terminal
M34
1
Battery voltage
2
Terminals
Continuity
(+)
(-)
Combination meter
Ground
Connector
Terminal
M34
3
Existed
23
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст