Nissan Teana J32. Instruction — part 639
GW-10
< ON-VEHICLE REPAIR >
WINDSHIELD GLASS
ON-VEHICLE REPAIR
WINDSHIELD GLASS
Exploded View
INFOID:0000000003825397
JMKIA2306GB
WINDSHIELD GLASS
GW-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Removal and Installation
INFOID:0000000003825398
REMOVAL
1.
Remove front pillar garnish (LH/RH). Refer to
INT-39, "Removal and Installation"
.
2.
Remove partially headlining (front edge). Refer to
INT-50, "NORMAL ROOF : Removal and Installation"
for normal roof or
INT-54, "SUNROOF : Removal and Installation"
for sunroof.
3.
Remove front wiper arms (LH/RH). Refer to
WW-105, "Removal and Installation"
4.
Remove front fender cover (LH/RH). Refer to
.
5.
Remove cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
6.
Remove roof side molding (LH/RH). Refer to
EXT-29, "Removal and Installation"
.
7.
Remove glass using piano wire or power cutting tool (A) and an inflatable pump bag (B) after removing
moldings.
NOTE:
Mark the body and the glass with matching marks if the windshield glass is reused.
WARNING:
Always wear safety glasses and heavy gloves to prevent injury.
CAUTION:
• Never use a cutting knife or power cutting tool when the windshield glass is reused.
• Be careful not to scratch the glass when removing.
• Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam sealant rubber should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions provided
with it.
• Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger compartment air pressure when all door windows are closed.
• The molding must be installed securely so that it is in position and leaves no clearance.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them come in contact with skin or eyes.
1.
Windshield molding (upper)
2.
Dam sealant rubber
3.
Spacer (LH/RH)
4.
Windshield glass assembly
5.
Roof side molding (LH/RH)
6.
Front fender cover
7.
Roof side molding fastener
8.
Mirror base
9.
Adhesive
10.
Primer
11.
Cowl top center
12. Cowl top cover
13.
Roof
14. Headlining assembly
15. Front roof rail
16.
Body side outer
17. Front pillar inner upper
18. Front pillar garnish
19.
Front sunroof glass
: Clip
Unit
: mm (in)
Note
: D and E on the exploded view are sections of sunroof models.
Refer to
for symbols in the figure.
PIIB5779E
GW-12
< ON-VEHICLE REPAIR >
WINDSHIELD GLASS
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Perform adjustment of front wiper arms stop location. Refer to
.
• Never use an adhesive which is past its usable term. Shelf life of this product is limited to six months
after the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the
box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Never leave primers or adhesive cartridge unattended with their caps open or off.
• Never drive the vehicle within 24 hours or until the urethane adhesive has completely cured. Curing
time varies depending on temperature and humidity. The curing time increases under lower temper-
ature and lower humidity.
Inspection
INFOID:0000000003825399
REPAIRING WATER LEAKAGE FOR WINDSHIELD
Leakage can be repaired without removing the glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the windshield area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
SIDE WINDOW GLASS
GW-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
SIDE WINDOW GLASS
Exploded View
INFOID:0000000003825400
Removal and Installation
INFOID:0000000003825401
REMOVAL
1.
Remove rear seatback and rear seat cushion. Refer to
SE-99, "Removal and Installation"
.
2.
Remove rear pillar finisher. Refer to
INT-39, "Removal and Installation"
3.
Apply protective tape around the side window to protect the painted surface from damage.
4.
Remove side window glass using piano wire.
1.
Side window glass
2.
Side window glass assembly
3.
Primer
4.
Adhesive
5.
Body side outer
6.
Clip
Unit
: mm (in)
Refer to
for symbols in the figure.
JMKIA2308GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст