Nissan Teana J32. Instruction — part 423
EC-230
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
P0420, P0430 THREE WAY CATALYST FUNCTION
Check the initial spark plug for fouling, etc.
Is the inspection result normal?
YES
>> Replace spark plug(s) with standard type one(s). For
spark plug type, refer to
.
NO
>> Repair or clean spark plug. Then GO TO 9.
9.
CHECK FUNCTION OF IGNITION COIL-III
1.
Reconnect the initial spark plugs.
2.
Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and
the grounded portion.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace spark plug(s) with standard type one(s). For spark plug type, refer to
.
10.
CHECK FUEL INJECTOR
1.
Turn ignition switch OFF.
2.
Remove fuel injector assembly.
Refer to
EM-44, "Removal and Installation"
Keep fuel hose and all fuel injectors connected to fuel tube.
3.
Disconnect all ignition coil harness connectors.
4.
Reconnect all fuel injector harness connectors disconnected.
5.
Turn ignition switch ON.
Check the fuel does not drip from fuel injector.
Does fuel drip from fuel injector?
YES
>> Replace the fuel injector(s) from which fuel is dripping.
NO
>> GO TO 11.
11.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
Is the inspection result norma?
YES
>> Replace three way catalyst assembly.
NO
>> Repair or replace harness or connector.
SEF156I
Spark should be generated.
P0444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-231
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Description
INFOID:0000000003856644
The EVAP canister purge volume control solenoid valve is used to
control the flow rate of fuel vapor from the EVAP canister. The EVAP
canister purge volume control solenoid valve is moved by ON/OFF
pulses from the ECM. The longer the ON pulse, the greater the
amount of fuel vapor that will flow through the valve.
DTC Logic
INFOID:0000000003856645
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm battery voltage is more than 11 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for at least 13 seconds.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003856646
1.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect EVAP canister purge volume control solenoid valve harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between EVAP canister purge volume control solenoid valve harness connector and
ground.
Is the inspection result normal?
PBIB3489E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0444
EVAP canister purge volume
control solenoid valve circuit
open
An excessively low voltage signal is sent
to ECM through the valve
• Harness or connectors
(The solenoid valve circuit is open or
shorted.)
• EVAP canister purge volume control so-
lenoid valve
EVAP canister purge volume control
solenoid valve
Ground
Voltage
Connector
Terminal
F30
1
Ground
Battery voltage
EC-232
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
P0444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F121, E7
• Harness for open or short between EVAP canister purge volume control solenoid valve and IPDM E/R
• Harness for open or short between EVAP canister purge volume control solenoid valve and ECM
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT
FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between EVAP canister purge volume control solenoid valve harness connector and
ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES-1 >> With CONSULT-III: GO TO 4.
YES-2 >> Without CONSULT-III: GO TO 5.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT-III
1.
Reconnect all harness connectors disconnected.
2.
Start engine.
3.
Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode with CONSULT-III. Check that engine speed var-
ies according to the valve opening.
Does engine speed vary according to the valve opening?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-232, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace EVAP canister purge volume control solenoid valve.
6.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000003856647
1.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT-III
1.
Turn ignition switch OFF.
2.
Reconnect all harness connectors disconnected.
3.
Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.
EVAP canister purge volume con-
trol solenoid valve
ECM
Continuity
Connector
Terminal
Connector
Terminal
F30
2
F7
25
Existed
P0444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-233
< COMPONENT DIAGNOSIS >
[VQ25DE, VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4.
Turn ignition switch ON.
5.
Select “PURG VOL CONT/V” in “ACTIVE TEST” mode with CONSULT-III.
6.
Touch “Qd” and “Qu” on CONSULT-III screen to adjust “PURG
VOL CONT/V” opening and check air passage continuity of
EVAP canister purge volume control solenoid valve under the
following conditions.
Without CONSULT-III
1.
Turn ignition switch OFF.
2.
Disconnect EVAP canister purge volume control solenoid valve harness connector.
3.
Disconnect EVAP purge hoses connected to EVAP canister purge volume control solenoid valve.
4.
Check air passage continuity of EVAP canister purge volume
control solenoid valve under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace EVAP canister purge volume control solenoid
valve
Condition
(PURG VOL CONT/V value)
Air passage continuity
between (A) and (B)
100%
Existed
0%
Not existed
PBIB2058E
Condition
Air passage continuity
between (A) and (B)
12 V direct current supply between
terminals 1 and 2
Existed
No supply
Not existed
PBIB2059E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст