Nissan Teana J32. Instruction — part 548
EXL-162
< ECU DIAGNOSIS >
[XENON TYPE]
AUTO LEVELIZER CONTROL UNIT
DTC Inspection Priority Chart
INFOID:0000000003805625
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
B2082: SENSOR OUT OF
RANGE
After engine start
[Less than 5 seconds after ig-
nition switch ON and vehicle
speed less than 4 km/h (2.5
MPH)]
Fix with the light axis facing
downward
When sensor signal returns to
normal range
While driving
[5 seconds or more after igni-
tion switch ON or vehicle
speed 4 km/h (2.5 MPH) or
more]
Maintain the light axis at the
time of DTC detection
B2083: SEN SIG NOT PLAU-
SIBLE
• Maintain the aiming motor drive signal output at the time of
DTC detection
• Maintain the light axis at the time of DTC detection
Ignition switch OFF
B2084: VOLTAGE UNDER
LIMIT
After engine start
[Less than 5 seconds after ig-
nition switch ON and vehicle
speed less than 4 km/h (2.5
MPH)]
Fix with the light axis facing
downward
Ignition switch OFF
While driving
[5 seconds or more after igni-
tion switch ON or vehicle
speed 4 km/h (2.5 MPH) or
more]
Maintain the light axis at the
time of DTC detection
B2085: LOWBEAM SIG
OPEN LINE
After engine start
[Less than 5 seconds after ig-
nition switch ON and vehicle
speed less than 4 km/h (2.5
MPH)]
Fix with the light axis facing
downward
Ignition switch OFF
While driving
[5 seconds or more after igni-
tion switch ON or vehicle
speed 4 km/h (2.5 MPH) or
more]
Maintain the light axis at the
time of DTC detection
B2086: FRQ. OVER LIMIT
After engine start
[Less than 5 seconds after ig-
nition switch ON and vehicle
speed less than 4 km/h (2.5
MPH)]
Fix with the light axis facing
downward
Ignition switch OFF
While driving
[5 seconds or more after igni-
tion switch ON or vehicle
speed 4 km/h (2.5 MPH) or
more]
Maintain the light axis at the
time of DTC detection
B2087: SHORT TO GROUND
Maintain the light axis at the time of DTC detection
Ignition switch OFF
B2088: SHORT TO BATTERY
Maintain the light axis at the time of DTC detection
Ignition switch OFF
B208A: PARA NOT PROG
Fix aiming motor drive signal output to approximately 0 V
Write configuration is complet-
ed
DTC
Fail-safe
Cancellation
Priority
DTC
1
• B2080: ECU TROUBLE
• B208A: PARA NOT PROG
AUTO LEVELIZER CONTROL UNIT
EXL-163
< ECU DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DTC Index
INFOID:0000000003805626
2
• B2081: INITIAL NOT DONE
3
• B2082: SENSOR OUT OF RANGE
• B2083: SEN SIG NOT PLAUSIBLE
• B2084: VOLTAGE UNDER LIMIT
• B2085: LOWBEAM SIG OPEN LINE
• B2086: FRQ. OVER LIMIT
• B2087: SHORT TO GROUND
• B2088: SHORT TO BATTERY
Priority
DTC
DTC
Fail-safe
Refer to
B2080: ECU TROUBLE
×
B2081: INITIAL NOT DONE
×
B2082: SENSOR OUT OF RANGE
×
B2083: SEN SIG NOT PLAUSIBLE
×
B2084: VOLTAGE UNDER LIMIT
×
B2085: LOWBEAM SIG OPEN LINE
×
B2086: FRQ. OVER LIMIT
×
B2087: SHORT TO GROUND
×
B2088: SHORT TO BATTERY
×
B208A: PARA NOT PROG
×
EXL-164
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000003774367
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp (HI) is not
turned ON.
One side
• Fuse
• Halogen bulb (HI)
• Harness between IPDM E/R
and the headlamp high
• IPDM E/R
Headlamp (HI) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
Headlamp (HI) is not
turned OFF.
When ignition switch is
turned ON.
When ignition switch is
turned OFF.
IPDM E/R
—
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEAD LAMP)
Active test “HEADLAMP”
Headlamp (LO) is not
turned ON.
One side
• Fuse
• Xenon bulb (LO)
• Harness between IPDM E/R
and the front combination lamp
• IPDM E/R
Headlamp (LO) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
Headlamp (LO) is not
turned OFF.
When ignition switch is
turned ON.
When ignition switch is
turned OFF.
IPDM E/R
—
Each lamps are not turned ON/OFF with lighting
switch AUTO.
• Combination switch
• Harness between the combina-
tion switch and BCM
• BCM
Combination switch
Refer to
• Optical sensor
• Harness between the optical
sensor and BCM
• BCM
Optical sensor circuit
Refer to
.
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R
and the front fog lamp
• Front fog lamp
• IPDM E/R
Front fog lamp circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
Front fog lamp is not turned ON.
Front fog lamp indicator is not turned ON.
(Front fog lamp is turned ON.)
Combination meter
• Combination meter
Data monitor “FR FOG IND”
• BCM (HEAD LAMP)
Active test “FR FOG LAMP”
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-165
< SYMPTOM DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Parking lamp is not turned ON.
• Parking lamp bulb
• Harness between IPDM E/R
and the front combination lamp
• Front combination lamp
• IPDM E/R
Parking lamp circuit
Refer to
.
Tail lamp is not turned ON.
• Harness between IPDM E/R
and the rear combination lamp
• Rear combination lamp
Tail lamp circuit
Refer to
.
License plate lamp is not turned ON.
• License plate lamp bulb
• Harness between IPDM E/R
and the license plate lamp
• License plate lamp
License plate lamp circuit
Refer to
.
Tail lamp and the license plate lamp are not turned
ON.
• Fuse
• Harness between IPDM E/R
and the rear combination lamp
• IPDM E/R
License plate lamp circuit
Refer to
.
• Parking lamp, the tail lamp and the license plate
lamp are not turned ON.
• Parking lamp, the tail lamp and the license plate
lamp are not turned OFF.
(Each illumination is turned ON/OFF.)
Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED
ON”
Refer to
Tail lamp indicator is not turned ON.
(Parking, tail lamps are turned ON.)
Combination meter
• Combination meter
Data monitor “LIGHT IND”
• BCM (HEAD LAMP)
Active test “TAIL LAMP”
Turn signal lamp does not
blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)
• Harness between BCM and
each turn signal lamp
• Turn signal lamp bulb
Turn signal circuit
Refer to
.
Indicator lamp is includ-
ed.
• Combination switch
• Harness between the combina-
tion switch and BCM
• BCM
Combination switch
Refer to
.
Turn signal indicator lamp
does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp sig-
nal
- BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF)
• Combination meter power sup-
ply and the ground circuit
• Combination meter
Combination meter
Power supply and the ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between the hazard
switch and BCM
• BCM
Hazard switch
Refer to
.
Rear fog lamp is not
turned ON.
Rear fog lamp indicator
lamp is normal.
• Harness between BCM and the
rear fog lamp
• Rear fog lamp bulb
• BCM
Rear fog lamp circuit
Refer to
.
Rear fog lamp indicator
lamp is included.
• Combination switch
• Harness between the combina-
tion switch and BCM
• BCM
Combination switch
Refer to
.
Symptom
Possible cause
Inspection item
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст