Nissan Teana J32. Instruction — part 355
FRONT DOOR
DLK-203
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-203, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DOOR ASSEMBLY : Adjustment
INFOID:0000000003813396
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
1.
Remove front fender. Refer to
DLK-199, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install front fender. Refer to
DLK-199, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000003819380
Portion
Clearance
Surface height
Front fender – Front door
A – A
2.6 – 4.6 (0.102 – 0.181)
−
1.0 – 1.0 (
−
0.039 – 0.039)
Front door – Rear door
B – B
3.6 – 5.6 (0.142 – 0.220)
−
1.0 – 1.0 (
−
0.039 – 0.039)
JMKIA2384ZZ
DLK-204
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
DOOR STRIKER : Removal and Installation
INFOID:0000000003813398
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-203, "DOOR ASSEMBLY : Adjust-
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000003819407
DOOR HINGE : Removal and Installation
INFOID:0000000003813400
REMOVAL
1.
Remove front fender. Refer to
DLK-199, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-202, "DOOR ASSEMBLY : Removal and Installation"
.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA2384ZZ
FRONT DOOR
DLK-205
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Remove front door hinge mounting bolts, and then remove front door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-203, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts
and bolts.
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000003819408
DOOR CHECK LINK : Removal and Installation
INFOID:0000000003813402
REMOVAL
1.
Remove front door finisher. Refer to
INT-30, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-33, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Fully close the front door window.
3.
Remove front door speaker.
4.
Remove mounting bolts of door check link on the vehicle.
5.
Remove mounting bolts of door check link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
1.
Front door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Refer to
JMKIA2384ZZ
DLK-206
< ON-VEHICLE REPAIR >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR
Install in the reverse order of removal.
CAUTION:
Check front door open/close operation after installation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст