Nissan Teana J32. Instruction — part 955
RF-86
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
SUNROOF UNIT ASSEMBLY
Exploded View
INFOID:0000000003812891
REMOVAL
1.
Roof side finisher RH
2.
Rear link cover
3.
TORX bolt
4.
Glass lid
5.
Roof side finisher LH
6.
Inner blind
7.
Sunroof unit assembly
8.
Sunroof motor assembly
9.
Sunshade motor assembly
Refer to
for symbols in the figure.
JMKIA2488GB
SUNROOF UNIT ASSEMBLY
RF-87
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
DISASSEMBLY
1.
Sunroof frame
2.
Front sunroof glass
3.
Adhesive
4.
Windshield molding
5.
Windshield glass
6.
Roof panel
7.
Primer
8.
Rear sunroof glass
9.
Rear window glass
Refer to
JMKIA2507GB
RF-88
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
Removal and Installation
INFOID:0000000003812892
REMOVAL
CAUTION:
• Always work with a helper.
• Never reuse the front and rear sunroof glass which has been removed once.
1.
Remove the headlining. Refer to
INT-54, "SUNROOF : Removal and Installation"
2.
Remove the glass lid. Refer to
RF-80, "Removal and Installation"
3.
Remove the windshield molding. Refer to
GW-11, "Removal and Installation"
.
4.
Paint matching marks on body before removing the sunroof unit assembly.
5.
Remove nuts and bolts from the front end, side rail and rear end.
6.
Apply protective tape around the roof panel to protect the surface from damage.
1.
Weather-strip
2.
Wind deflector
3.
Sunroof frame
4.
Front sunshade
5.
Sunshade cover
6.
Rear sunshade
Refer to
for symbols in the figure.
JMKIA2489GB
SUNROOF UNIT ASSEMBLY
RF-89
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
7.
Remove the front sunroof glass. Refer to
RF-91, "Removal and Installation"
.
8.
Cut adhesive.
• Cut the resin part of the rear sunroof glass rear using cutter
(A).
• Cut the adhesive using windshield cutter (A).
• Pass piano wire though the adhesive with a wire pierce.
• Tie both ends of piano wire to wire grip.
• Pull piano wire in turn and cut off adhesive.
9.
Remove sunroof unit assembly from vehicle.
INSTALLATION
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
CAUTION:
After installing the sunroof unit assembly and glass lid, perform the leak test and check that there is
no malfunction.
NOTE:
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions fur-
nished with it.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
1.
Using a knife or spatula, trim the adhesive (sealant) remaining
on body down to approximately 2 mm thick (a) so that the con-
tour becomes smooth.
CAUTION:
If bonded area on body is scratched, always repair it with 2-
component urethane. Never use lacquer.
JMKIA2510ZZ
PIIB3505J
JMKIA0307ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст