Nissan Teana J32. Instruction — part 323
TRUNK LID OPENER REQUEST SWITCH
DLK-75
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK TRUNK LID OPENER REQUEST SWITCH GROUND CIRCUIT
Check continuity between trunk lid opener request switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TRUNK LID OPENER REQUEST SWITCH
DLK-75, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace trunk lid opener request switch. Refer to
DLK-242, "Removal and Installation"
5.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003794881
1.
CHECK TRUNK LID OPENER REQUEST SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect trunk lid opener request switch connector.
3.
Check trunk lid opener request switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace trunk lid opener request switch. Refer to
DLK-242, "Removal and Installation"
Trunk lid opener request switch
Ground
Continuity
Connector
Terminal
T6
2
Existed
Trunk lid opener request switch
Condition
Continuity
Terminal
1
2
Trunk lid opener request
switch
Pressed
Existed
Released
Not existed
DLK-76
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
TRUNK ROOM LAMP SWITCH
TRUNK ROOM LAMP SWITCH
Description
INFOID:0000000003840907
Detects trunk lid open/close condition.
Component Function Check
INFOID:0000000003840908
1.
CHECK FUNCTION
With CONSULT-III
Check (“TRNK/HAT MNTR”) in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES
>> Trunk room lamp switch is OK.
NO
>> Refer to
DLK-77, "Component Inspection"
Diagnosis Procedure
INFOID:0000000003840909
1.
CHECK TRUNK ROOM LAMP SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect trunk lid lock assembly.
3.
Check signal between BCM connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TRUNK ROOM LAMP SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector and trunk lid lock assembly connector.
3.
Check continuity between BCM connector and ground.
Monitor item
Condition
TRNK/HAT MNTR
OPEN
: ON
CLOSE
: OFF
(+)
(–)
Trunk
condition
Signal
(Reference value)
Trunk lid lock assembly
Connector
Terminal
T5
1
Ground
OPEN
0
CLOSE
JPMIA0011GB
BCM
Trunk lid lock assembly
Continuity
Connector
Terminal
Connector
Terminal
M121
50
T5
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M121
50
Not existed
TRUNK ROOM LAMP SWITCH
DLK-77
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK TRUNK ROOM LAMP SWITCH GROUND CIRCUIT
Check continuity between trunk lid lock assembly connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TRUNK ROOM LAMP SWITCH
DLK-77, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace trunk lid lock assembly. Refer to
DLK-214, "TRUNK LID ASSEMBLY : Removal and
5.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END.
Component Inspection
INFOID:0000000003840910
1.
CHECK TRUNK ROOM LAMP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect trunk lid lock assembly connector.
3.
Check trunk room lamp switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace trunk lid lock assembly. Refer to
DLK-214, "TRUNK LID ASSEMBLY : Removal and
Trunk lid lock assembly
Ground
Continuity
Connector
Terminal
T5
3
Existed
Trunk lid lock assembly
Condition
Continuity
Terminal
1
3
Trunk lid
OPEN
Existed
CLOSE
Not existed
DLK-78
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
UNLOCK SENSOR
UNLOCK SENSOR
Description
INFOID:0000000003794882
Detects door lock condition of driver door.
Component Function Check
INFOID:0000000003794883
1.
CHECK FUNCTION
Check unlock sensor (“DOOR STAT-DR”) in “Data Monitor” mode.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000003794884
1.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) (unlock sensor) connector.
3.
Check signal between front door lock assembly (driver side) (unlock sensor) harness connector and
ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) (unlock sen-
sor) harness connector.
3.
Check continuity between BCM harness connector and ground.
Monitor item
Condition
DOOR STAT-DR
Front door lock (driver side) LOCK: OFF
Front door lock (driver side) UNLOCK: ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (driver side) (unlock sensor)
Connector
Terminal
D9
3
Ground
JPMIA0012GB
BCM
Front door lock assembly
(driver side) (unlock sensor)
Continuity
Connector
Terminal
Connector
Terminal
M123
119
D9
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M123
119
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст