Nissan Teana J32. Instruction — part 758
INT-52
< ON-VEHICLE REPAIR >
HEADLINING
CAUTION:
• When removing, 2 workers are required. (1 for the front and rear of headlining)
• Cover center console finisher upper surface with a shop cloth to prevent it from being damaged.
• Never bend headlining when removing.
13. Remove the following parts after removing headlining.
• Map lamp assembly. Refer to
INL-89, "Removal and Installation"
• Personal lamp assembly. Refer to
INL-96, "Removal and Installation"
.
• Roof harness assembly.
• Antenna feeder assembly. Refer to
.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Install headlining assembly after inserting clips to clip holder of headlining rear end.
• Never bend headlining when installing.
SUNROOF
HEADLINING
INT-53
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
SUNROOF : Exploded View
INFOID:0000000003826877
1.
Antenna feeder (rear)
2.
Assist grip
3.
Antenna feeder (front)
4.
Sun visor assembly RH
5.
Sun visor cover
6.
Sun visor holder
7.
Sun visor assembly LH
8.
Roof harness
9.
Headlining assembly
10. Rear hidden clip
11. Roof insulator
12. Dual lock fastener
13. Over head console
14. Roof bracket
15. Roof plate assembly
16. Map lamp lens RH
17. Map lamp lens LH
18. Assist grip clip
19. Personal lamp bracket
20. Personal lamp bulb
21. Personal lamp cover
22. Personal lamp lens
JMJIA1805ZZ
INT-54
< ON-VEHICLE REPAIR >
HEADLINING
SUNROOF : Removal and Installation
INFOID:0000000003826878
REMOVAL
1.
Remove front body side welt (LH/RH) and front pillar garnish (LH/RH). Refer to
.
2.
Disconnect the roof harness (1) connector (B), antenna feeder (2) harness connector (C) and then
remove all the clips (A) as shown in the figure below.
3.
Remove sun visor assembly (LH/RH).
• Remove sun visor cover.
• Remove sun visor assembly (1) mounting screws (B) with a
screwdriver (A).
• Disconnect vanity mirror lamp harness connectors.
4.
Rotate 90 degrees and remove sun visor holder (1) (LH/RH).
: Pawl
: Metal clip
: Clip
JMJIA1785ZZ
JMJIA1786ZZ
JMJIA1787ZZ
HEADLINING
INT-55
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
5.
Remove mounting plastic clips (A) using a flat-bladed screw-
driver (B) of front and rear assistance grips (1), and then remove
assist grips.
6.
Remove the front seat assembly. Refer to
SE-92, "Removal and Installation"
.
7.
Remove rear seat assembly. Refer to
SE-99, "Removal and Installation"
.
8.
Remove front kicking plate inner (LH/RH), center pillar upper garnish (LH/RH) and rear pillar finisher (LH/
RH).
Refer to
INT-39, "Removal and Installation"
9.
On the rear right side of the vehicle, disconnect the harness
connector (A) and (C), remove the bolt (B) and then disengage
the pawls as shown in the figure.
10. With a removal tool, remove body side mounting plastic clip from rear end of headlining.
11. Pull map lamp assembly toward vehicle lower, and disengage
dual-lock fastener (A) and metal clips (B).
CAUTION:
Map lamp assembly is crimped from back of headlining.
Remove it by disengaging the crimped area of back of map
lamp assembly after removing headlining from the vehicle.
12. Remove headlining assembly (1) as shown in the figure below.
JMJIA0096GB
: Pawl
JMJIA1788ZZ
JMJIA1008ZZ
JMJIA1789ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст