Nissan Teana J32. Instruction — part 1184
TM-260
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
P1745 LINE PRESSURE CONTROL
P1745 LINE PRESSURE CONTROL
Description
INFOID:0000000003806468
The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pres-
sure to suit the driving condition in response to the signal sent from the TCM.
DTC Logic
INFOID:0000000003806469
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Turn ignition switch ON
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Make sure that output voltage of CVT fluid temperature sensor is within the range below.
Is “P1745 L/PRESS CONTROL” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003806470
1.
CHECK DTC
With CONSULT-III
1.
Start engine.
2.
Select “Self Diagnostic Results” mode for “TRANSMISSION”.
Is the “P1745 L/PRESS CONTROL” displayed?
YES
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P1745
L/PRESS CONTROL
TCM detects the unexpected
line pressure.
TCM
ATF TEMP SEN
: 1.0 – 2.0 V
If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the
voltage (cool down the fluid)
P1777 STEP MOTOR
TM-261
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P1777 STEP MOTOR
Description
INFOID:0000000003806471
The step motor changes the step by turning 4 coils ON/OFF according to the signal from TCM. As a result, the
flow of line pressure to primary pulley is changed and pulley ratio is controlled.
DTC Logic
INFOID:0000000003806472
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start engine.
2.
Drive vehicle for at least 5 consecutive seconds.
3.
Select “Self Diagnostic Results” mode for “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is “P1777 STEP MOTR CIRC” detected?
YES
>> Go to
NO
>> Check intermittent incident. Refer to
GI-35, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000003806473
1.
CHECK STEP MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check resistance between TCM vehicle side harness connector terminals.
4.
Check resistance between TCM vehicle side harness connector terminals and ground.
DTC
Item
(CONSULT-III screen term)
Malfunction is detected when...
Possible cause
P1777
STEP MOTR CIRC
Each coil of the step motor is
not energized properly due to
an open or a short.
• Step motor
• Harness or connectors
(Step motor circuit is open or
shorted.)
TCM vehicle side harness connector
Resistance (Approx.)
Connector
Terminal
F23
27
28
30.0
Ω
29
30
TM-262
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
P1777 STEP MOTOR
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (STEP MOTOR) (PART 1)
1.
Disconnect CVT unit harness connector.
2.
Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN TCM AND CVT UNIT (STEP MOTOR) (PART 2)
Check continuity between TCM vehicle side harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK STEP MOTOR
Check step motor. Refer to
TM-263, "Component Inspection (Step Motor)"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace damaged parts.
5.
DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
NO
>> Repair or replace damaged parts.
TCM vehicle side harness connector
Ground
Resistance (Approx.)
Connector
Terminal
F23
27
15.0
Ω
28
29
30
TCM vehicle side harness connector
CVT unit vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
F23
27
F24
9
Existed
28
8
29
7
30
6
TCM vehicle side harness connector
Ground
Continuity
Connector
Terminal
F23
27
Not existed
28
29
30
P1777 STEP MOTOR
TM-263
< COMPONENT DIAGNOSIS >
[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Component Inspection (Step Motor)
INFOID:0000000003806474
1.
STEP MOTOR
Check resistance between CVT unit connector terminals and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the transaxle assembly. Refer to
.
CVT unit connector
Resistance (Approx.)
Connector
Terminal
F24
6
7
30.0
Ω
8
9
CVT unit connector
Ground
Resistance (Approx.)
Connector
Terminal
F24
6
15.0
Ω
7
8
9
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст