Nissan Teana J32. Instruction — part 1023
SEC-80
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B260D STEERING LOCK UNIT
B260D STEERING LOCK UNIT
Description
INFOID:0000000003815008
The steering lock unit performs the check by itself according to the steering lock status (before lock, after lock
and unlock).
DTC Logic
INFOID:0000000003815009
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF.
3.
Press driver side door switch.
4.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003815010
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is the DTC B260D displayed again?
YES
>> Replace steering lock unit.
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B260D
STEERING LOCK UNIT
BCM detects malfunctioning of steering lock unit after
steering locking.
Steering lock unit
B260F ENGINE STATUS
SEC-81
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B260F ENGINE STATUS
Description
INFOID:0000000003815011
BCM receives the engine status signal from ECM via CAN communication.
DTC Logic
INFOID:0000000003815012
DTC DETECTION LOGIC
NOTE:
• If DTC B260F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B260F is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003815013
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is the DTC B260F displayed again?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
REPLACE ECM
Replace ECM. Refer to
EC-14, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
.
>> INSPECTION END
3.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B260F
INTERRUPTION OF ENGINE STATUS SIGNAL
BCM has not yet received the engine status sig-
nal from ECM when ignition switch is in the ON
position
ECM
SEC-82
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
Description
INFOID:0000000003815014
BCM receives the engine status signal from ECM via CAN communication.
DTC Logic
INFOID:0000000003815015
DTC DETECTION LOGIC
NOTE:
• If DTC B26E1 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B26E1 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003815016
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is the DTC B26E1 displayed again?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
REPLACE ECM
Replace ECM. Refer to
EC-14, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
.
>> INSPECTION END
3.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B26E1
NO RECEPTION OF ENGINE STATUS SIGNAL
BCM does not receive the engine status signal
from ECM when ignition switch is in the ON po-
sition
ECM
B26E9 STEERING STATUS
SEC-83
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B26E9 STEERING STATUS
Description
INFOID:0000000003815017
There are 2 switches in the steering lock unit (steering lock/unlock switch 1 and 2). BCM compares those 2
switches conditions to judge the present steering status.
DTC Logic
INFOID:0000000003815018
DTC DETECTION LOGIC
NOTE:
• If DTC B26E9 is displayed with DTC B2609, first perform the trouble diagnosis for DTC B2609. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF.
3.
Press driver side door switch and wait for at least 1 second.
4.
Turn ignition switch ON.
5.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003815019
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
Refer to
.
Is the DTC B26E9 displayed again?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
REPLACE STEERING LOCK UNIT
1.
Replace steering lock unit.
2.
Perform DTC confirmation procedure. Refer to
.
Is the DTC B26E9 displayed again?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK INTERMITTENT INCIDENT
GI-35, "Intermittent Incident"
.
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B26E9
S/L STATUS
BCM requests lock to steering lock unit, then steer-
ing lock unit transmits a recognition signal to BCM,
but steering lock unit remains unlocked.
Steering lock unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст