Nissan Teana J32. Instruction — part 796
ENGINE OIL
LU-9
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
4.
Remove drain plug (1) and then drain engine oil.
Refilling
INFOID:0000000003793123
1.
Install drain plug with new washer. Refer to
.
CAUTION:
Be sure to clean drain plug and install with new washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-11, "Fluids and Lubricants"
CAUTION:
• When filling engine oil, never pull out oil level gauge.
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in engine.
3.
Warm up the engine and check area around drain plug and oil filter for engine oil leakage.
4.
Stop the engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
.
: Vehicle front
JPBIA1676ZZ
Tightening torque
Engine oil capacity
: Refer to
LU-10
< ON-VEHICLE MAINTENANCE >
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000003793124
REMOVAL
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN oil filter or equivalent.
• Be careful not to get burned when engine and engine oil may be hot.
• When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.
• Never allow engine oil to adhere to drive belt.
• Completely wipe off any engine oil that adheres to engine and vehicle.
1.
Remove splash guard (RH). Refer to
EXT-22, "FENDER PROTECTOR : Exploded View"
.
2.
Using oil filter wrench [SST: KV10115801 (J38956)] (A), remove
oil filter.
INSTALLATION
1.
Remove foreign materials adhering to oil filter installation surface.
2.
Apply engine oil to the oil seal contact surface of new oil filter.
3.
Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to the specification.
Inspection
INFOID:0000000003793125
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
: Vehicle front
JPBIA1678ZZ
SMA010
Oil filter:
: 17.6 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
OIL COOLER
LU-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
ON-VEHICLE REPAIR
OIL COOLER
Exploded View
INFOID:0000000003793127
Removal and Installation
INFOID:0000000003793128
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
NOTE:
When remove oil cooler only, step 2 is unnecessary.
1.
Remove splash guard (RH). Refer to
EXT-22, "FENDER PROTECTOR : Exploded View"
.
2.
Drain engine coolant from radiator and cylinder block. Refer to
and
NOTE:
Perform this step when removing water pipes.
3.
Remove oil filter. Refer to
LU-10, "Removal and Installation"
CAUTION:
Never spill engine oil on drive belt.
1.
Connector bolt
2.
Copper gasket
3.
Water drain plug
4.
Water pipe
5.
Bracket
6.
Clamp
7.
Water hose
8.
Relief valve
9.
Oil cooler
10.
Connector bolt
11.
Oil filter
12.
Water hose
13.
Water pipe
14.
Water hose
A.
To water connector
B.
Refer to
: Engine front
for symbols in the figure.
JPBIA1679GB
LU-12
< ON-VEHICLE REPAIR >
OIL COOLER
4.
Disconnect water hoses from oil cooler.
• When removing oil cooler only, pinching water hoses near oil cooler to prevent engine coolant from spill-
ing out.
• Remaining engine coolant in piping will come out. Use a tray to collect it.
CAUTION:
• Perform this step when the engine is cold.
• Never spill engine coolant on drive belt.
5.
Remove connector bolt, and remove oil cooler.
CAUTION:
Never spill engine oil to rubber parts such as drive belt.
6.
Remove water pipes, as necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Check that no foreign objects are adhering to the installation surfaces of oil cooler and oil pan (upper).
• Align cutout (B) on oil cooler (2) with protrusion (A) on oil pan
(upper) side, and tighten connector bolt (1).
Inspection
INFOID:0000000003793129
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.
Relief Valve
Inspect relief valve for movement, cracks and breaks by pushing the ball. If replacement is necessary, remove
relief valve by prying it out with a suitable tool. Install a new relief valve in place by tapping it.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
.
2.
Start the engine, and check there is no leakage of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
and
JPBIA1680ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст