Nissan Teana J32. Instruction — part 7
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-21
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
MEMORY FUNCTION : Component Parts Location
INFOID:0000000003859812
1.
BCM M118, M119, M122, M123
2.
Combination meter M34
3.
Key slot M99
4.
Seat memory switch D13
5.
Front door switch (driver side) B34
6.
Reclining motor (driver side) B454
7.
Lifting motor (front) (driver side)
B455
8.
Driver seat control unit B451,B452
9.
Sliding motor (driver side) B461
JMJIA1811ZZ
ADP-22
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
MEMORY FUNCTION : Component Description
INFOID:0000000003759079
CONTROL UNITS
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
EXIT ASSIST FUNCTION
10. Lifting motor (rear) (driver side) B456 11.
Power seat switch (driver side) B459
(sliding, lifting switch)
12. Power seat switch (driver side) B459
(reclining switch)
13. TCM (transmission control module)
F23
14. Control device (detention switch)
M57
15. ABS actuator and electric unit (con-
trol unit) E36
A.
Behind the combination meter
B.
View with seat cushion and seatback
pad removed
C.
Back side of the seat cushion
D.
Engine room (LH)
E.
View with the center console assem-
bly removed
F.
Engine room (RH)
Item
Function
Driver seat control unit
• The address of each part is recorded
• Operates each motor of seat to the registered position
Item
Function
Memory switch 1/2
The registration and memory function can be performed with its operation
Item
Function
Lifting sensor (front)
Detects the up/down position of seat lifting (front)
Lifting sensor (rear)
Detects the up/down position of seat lifting (rear)
Reclining sensor
Detects the tilt of seatback
Sliding sensor
Detects the front/rear position of seat
Item
Function
Lifting motor (front)
Moves the seat lifter (front) upward/downward
Lifting motor (rear)
Moves the seat lifter (rear) upward/downward
Reclining motor
Tilts and raises up the seatback
Sliding motor
Slides the seat frontward/rearward
Memory indicator
Illuminates or blinks according to the registration/operation status
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-23
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
EXIT ASSIST FUNCTION : System Diagram
INFOID:0000000003759080
EXIT ASSIST FUNCTION : System Description
INFOID:0000000003759081
OUTLINE
When opening the driver door while the operation condition is satisfied, the seat moves backward 40 mm
(1.57 in) from normal sitting position.
The seat slide amount operation at entry/exit operation can be changed.
NOTE:
• This function is set to ON before delivery (initial setting).
• Further information for the system setting procedure. Refer to
ADP-8, "SYSTEM INITIALIZATION : Descrip-
OPERATION PROCEDURE
1.
Open the driver door with ignition switch in the OFF position.(Intelligent Key is not inserted into key slot)
2.
Driver seat moves to the exiting position.
OPERATION CONDITION
Satisfy all of the following items. The exit assist function is not performed if any of these items are not satisfied.
JMJIA1816GB
Item
Request status
Ignition position
OFF
System setting [Entry/exit assist function (seat)]
ON
Initialization
Done
Key switch
OFF
(Intelligent Key is not inserted into key slot)
Switch inputs
• Power seat switch
• Set switch
• Memory switch
OFF
(Not operated)
Selector lever
P position
BCM
Handle position
ADP-24
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
DETAIL FLOW
Order
Input
Output
Control unit condition
1
Door switch
(Driver side)
—
Driver seat control unit receives door switch signal (driver side/
open) from BCM via CAN communication
2
—
Sliding motor
Driver seat control unit operates the seat sliding motor, which recog-
nizes that the driver side door is opened with ignition switch OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст