Nissan Teana J32. Instruction — part 850
PCS-6
< FUNCTION DIAGNOSIS >
[IPDM E/R]
RELAY CONTROL SYSTEM
Component Parts Location
INFOID:0000000003773257
1.
IPDM E/R
A.
Engine room (LH)
JPMIA1037ZZ
PCS
POWER CONTROL SYSTEM
PCS-7
< FUNCTION DIAGNOSIS >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER CONTROL SYSTEM
System Diagram
INFOID:0000000003773258
System Description
INFOID:0000000003773259
ALTERNATOR CONTROL
IPDM E/R outputs power generation command signal (PWM signal) to the alternator according to the status of
the power generation command value signal received from ECM via CAN communication. Refer to
.
Component Parts Location
INFOID:0000000003773260
JPMIA0908GB
1.
IPDM E/R
A.
Engine room (LH)
JPMIA1037ZZ
PCS-8
< FUNCTION DIAGNOSIS >
[IPDM E/R]
SIGNAL BUFFER SYSTEM
SIGNAL BUFFER SYSTEM
System Diagram
INFOID:0000000003773261
NOTE:
*: With BOSE audio system
System Description
INFOID:0000000003773262
• IPDM E/R reads the status of the oil pressure switch and transmits the oil pressure switch signal to BCM via
CAN communication. Refer to
MWI-22, "WARNING LAMPS/INDICATOR LAMPS : System Diagram"
• IPDM E/R reads the status of the hood switch and transmits the hood switch signal to BCM via CAN commu-
• IPDM E/R receives the rear window defogger control signal from BCM via CAN communication and trans-
mits it to ECM and AV control unit
*
via CAN communication. Refer to
DEF-4, "WITH AV CONTROL UNIT :
DEF-6, "WITHOUT AV CONTROL UNIT : System Diagram"
.
NOTE:
*: With BOSE audio system
Component Parts Location
INFOID:0000000003773263
JPMIA1043GB
1.
IPDM E/R
A.
Engine room (LH)
JPMIA1037ZZ
PCS
POWER CONSUMPTION CONTROL SYSTEM
PCS-9
< FUNCTION DIAGNOSIS >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER CONSUMPTION CONTROL SYSTEM
System Diagram
INFOID:0000000003857763
System Description
INFOID:0000000003773265
OUTLINE
• IPDM E/R incorporates a power consumption control function that reduces the power consumption accord-
ing to the vehicle status.
• IPDM E/R changes its status (control mode) with the sleep wake up signal received from BCM via CAN com-
munication.
Normal mode (wake-up)
- CAN communication is normally performed with other control units.
- Individual unit control by IPDM E/R is normally performed.
Low power consumption mode (sleep)
- Low power consumption control is active.
- CAN transmission is stopped.
SLEEP MODE ACTIVATION
• IPDM E/R judges that the sleep-ready conditions are fulfilled when the ignition switch is OFF and none of the
conditions below are present. Then it transmits a sleep-ready signal (ready) to BCM via CAN communica-
tion.
- Outputting signals to actuators
- Switches or relays operating
- Output requests are being received from control units via CAN communication.
• IPDM E/R stops CAN communication and enters the low power consumption mode when it receives a sleep
wake up signal (sleep) from BCM and the sleep-ready conditions are fulfilled.
WAKE-UP OPERATION
• IPDM E/R changes from the low power consumption mode to the normal mode when it receives a sleep
wake-up signal (wake up) from BCM or any of the following conditions is fulfilled. In addition, it transmits a
sleep-ready signal (not-ready) to BCM via CAN communication to report the CAN communication start.
- Ignition switch ON
- An output request is received from a control unit via CAN communication.
JPMIA1046GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст