Nissan Leaf. Instruction — part 930
LAN-182
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 4)]
IPDM-E BRANCH LINE CIRCUIT
IPDM-E BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010415436
1.
CHECK CONNECTOR
1. Turn the power switch OFF.
2. Disconnect the 12V battery cable from the negative terminal. Refer to
LAN-26, "Precautions for Removing
3. Check the terminals and connectors of the IPDM E/R for damage, bend and loose connection (unit side
and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of IPDM E/R.
2. Check the resistance between the IPDM E/R harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the IPDM E/R branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the IPDM E/R. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the IPDM E/R. Refer to
PCS-29, "Removal and Installation"
YES (Past error)>>Error was detected in the IPDM E/R branch line.
NO
>> Repair the power supply and the ground circuit.
IPDM E/R harness connector
Resistance (
Ω)
Connector No.
Terminal No.
E13
27
26
Approx. 54 – 66
LAN
DLC BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT)
LAN-183
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 4)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DLC BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT)
Diagnosis Procedure
INFOID:0000000010415437
1.
CHECK CONNECTOR
1. Turn the power switch OFF.
2. Disconnect the 12V battery cable from the negative terminal. Refer to
LAN-26, "Precautions for Removing
3. Check the terminals and connectors of the data link connector for damage, bend and loose connection
(connector side and harness side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
Check the resistance between the data link connector terminals.
Is the measurement value within the specification?
YES (Present error)>>Diagnose again. Refer to
LAN-17, "Trouble Diagnosis Flow Chart"
.
YES (Past error)>>Error was detected in the data link connector branch line circuit (CAN communication cir-
cuit side).
NO
>> Repair the data link connector branch line (CAN communication circuit side).
Data link connector
Resistance (
Ω)
Connector No.
Terminal No.
M4
6
14
Approx. 54 – 66
LAN-184
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 4)]
EPS BRANCH LINE CIRCUIT
EPS BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010415438
1.
CHECK CONNECTOR
1. Turn the power switch OFF.
2. Disconnect the 12V battery cable from the negative terminal. Refer to
LAN-26, "Precautions for Removing
3. Check the terminals and connectors of the EPS control unit for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of EPS control unit.
2. Check the resistance between the EPS control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the EPS control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the EPS control unit. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the steering column assembly. Refer to
ST-35, "Removal and Installation"
YES (Past error)>>Error was detected in the EPS control unit branch line.
NO
>> Repair the power supply and the ground circuit.
EPS control unit harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M37
2
1
Approx. 54 – 66
LAN
M&A BRANCH LINE CIRCUIT
LAN-185
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 4)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
M&A BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000010415439
1.
CHECK CONNECTOR
1. Turn the power switch OFF.
2. Disconnect the 12V battery cable from the negative terminal. Refer to
LAN-26, "Precautions for Removing
3. Check the terminals and connectors of the combination meter for damage, bend and loose connection
(unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of combination meter.
2. Check the resistance between the combination meter harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the combination meter branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the combination meter. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the combination meter. Refer to
MWI-102, "Removal and Installation"
YES (Past error)>>Error was detected in the combination meter branch line.
NO
>> Repair the power supply and the ground circuit.
Combination meter harness connector
Resistance (
Ω)
Connector No.
Terminal No.
M34
19
18
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст