Nissan Leaf. Instruction — part 598
EVC-416
< SYMPTOM DIAGNOSIS >
EV CONTROL SYSTEM
Normal Charge Does Not Start
INFOID:0000000010120867
Symptom
Possible cause
Action
Norm
al
ch
arg
e
do
es
no
t s
ta
rt
.
Normal charge start condi-
tions are not satisfied.
VCM recognizes that the se-
lector lever is in a range oth-
er than P range.
Electric shift system error.
Perform self-diagnosis of Electric
shift control module.
—
Power switch is not OFF.
Normal operation.
—
VCM receives a charge stop
request signal from PDM
(Power Delivery Module).
Check to see if charge stop condi-
tions are satisfied. Refer to
51, "LI-ION BATTERY CHARGE
CONTROL : Normal Charge Con-
trol"
VCM recognizes that quick
charge connector and nor-
mal charge connector are
connected simultaneously.
Abnormal connection detec-
tion circuit of quick charge
port.
Check quick charge port.
Abnormal PDM (Power De-
livery Module).
Perform self-diagnosis of PDM
(Power Delivery Module).
VCM prohibits charging.
Fail-safe of VCM.
VCM recognizes that nor-
mal charge connector is not
connected.
Abnormal connection detec-
tion circuit of normal charge
port.
Check normal charge port.
Abnormal PDM (Power De-
livery Module).
Perform self-diagnosis of PDM
(Power Delivery Module).
VCM recognizes that a
PWM signal is not received
from EVSE.
AC power, no input.
(Disconnect from outlet)
Check outlet.
AC power, no input.
(Blackout)
Check AC power.
EVSE does not transmit a
PWM signal.
Perform self-diagnosis of PDM
(Power Delivery Module).
Abnormal PDM (Power De-
livery Module).
—
Timer charge is set.
• Cancel timer charge setting.
• Turn ON the immediate charging
switch.
Judged as fully-charged.
—
Li-ion battery is fully
charged.
Normal operation.
EV CONTROL SYSTEM
EVC-417
< SYMPTOM DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
Timer Charge and Remote Charge Does Not Start
INFOID:0000000010120868
Symptom
Possible cause
Action
No
rma
l c
ha
rge
do
es
n
ot
st
art.
EVSE does not activate.
EVSE detects electric leak-
age
• Plug EVSE alone into an outlet
(AC source) and check that the
“Fault” lamp on EVSE does not
blink.
If the lamp blinks, replace EVSE.
• Check that no electric leakage
exists between EVSE control box
and PDM (Power Delivery Mod-
ule) or in the PDM (Power Deliv-
ery Module) itself.
EVSE has a malfunction
Plug EVSE alone into an outlet (AC
source) and check that the “Fault”
lamp of EVSE does not turn ON.
If the lamp turns ON, replace
EVSE.
EVSE not energized
Plug EVSE alone into an outlet (AC
source) and check that the
“Ready” lamp of EVSE turns ON.
If the lamp does not turn ON, re-
place EVSE.
EVSE communication line
has a malfunction
Plug EVSE alone into an outlet (AC
source) and check that the “Fault”
lamp on EVSE does not blink.
If the lamp blinks, replace EVSE.
Symptom
Possible cause
Action
T
imer c
ha
rge
or rem
ot
e
cha
rge
do
es
n
ot
st
ar
t.
The timer charge start con-
ditions are not satisfied.
—
Timer charge is not set.
Set timer charge.
The remote charge start
conditions are not satisfied.
Remote charge request is
not sent to the Information
Center (Nissan CARWINGS
Data Center).
The request is sent from an
out of service area.
Send a remote charge request in a
service area.
Remote charge request is
not sent from the Informa-
tion Center (Nissan CAR-
WINGS Data Center).
The vehicle is located an out
of service area.
Send a remote charge request in a
service area.
EVC-418
< SYMPTOM DIAGNOSIS >
EV CONTROL SYSTEM
Immediate Charge Does Not Start
INFOID:0000000010120869
Normal Charge Is Not Completed
INFOID:0000000010120870
Symptom
Possible cause
Action
Im
me
dia
te
ch
arg
e
do
es
no
t s
ta
rt.
Immediate charge start con-
dition are not satisfied.
—
Timer charge is set.
Turn ON the immediate charging
switch.
The operation of immediate
charging switch does not
start immediate charge.
Power switch is ON.
Turn power switch OFF.
A lapse of more than 15
minutes to connect the
charge connector after op-
erating the immediate
charging switch.
Connect charge connector within
15 minutes after operating the im-
mediate charging switch.
• Abnormal immediate
charging switch.
• Abnormal immediate
charging switch signal cir-
cuit.
EVC-390, "Diagnosis Procedure"
Symptom
Possible cause
Action
No
rmal
ch
arg
e
is n
o
t co
mpl
ete
d.
Normal charge is not completed despite full charge.
Abnormal LBC.
Perform self-diagnosis of LBC.
Timer charge is not completed.
Timer charge end time is not
set.
Set timer charge end time.
EV CONTROL SYSTEM
EVC-419
< SYMPTOM DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
Quick Charge Does Not Start
INFOID:0000000010120871
Quick Charge Is Not Completed
INFOID:0000000010120872
Symptom
Possible cause
Action
Q
ui
ck
c
ha
rge
do
es
n
ot
st
a
rt.
Quick charge start condi-
tions are not satisfied.
VCM recognizes that the se-
lector lever is in a range oth-
er than P range.
Electric shift system error.
Perform self-diagnosis of electric
shift control module.
—
Power switch is not OFF.
Normal operation.
—
VCM receives a charge stop
request signal from PDM
(Power Delivery Module).
Check that charging condition is
normal.
VCM recognizes that the
quick charge connector and
the normal charge connec-
tor are simultaneously con-
nected.
Abnormal connection detec-
tion circuit of normal charge
port.
Check normal charge port.
Abnormal PDM (Power De-
livery Module).
Perform self-diagnosis of PDM
(Power Delivery Module).
VCM prohibits charging.
Fail-safe of VCM.
VCM recognizes that the
quick charge connector is
not connected.
Abnormal connection detec-
tion circuit of quick charge
port.
Check quick charge port.
Abnormal PDM (Power De-
livery Module).
Perform self-diagnosis of PDM
(Power Delivery Module).
Quick charger does not per-
mit quick charge.
Quick charger detects insu-
lation resistance degrada-
tion in high voltage circuit.
Insulation resistance degra-
dation between PDM (Pow-
er Delivery Module) and
quick charger.
• Check PDM (Power Delivery
Module).
• Check high voltage harness.
• Check quick charge port.
• Check quick charger.
Symptom
Possible cause
Action
Qu
ic
k ch
arg
e
is
no
t c
om
ple
te
d.
Charging is not completed despite full charge.
Abnormal LBC.
Perform self-diagnosis of LBC.
VCM does not receive a quick charge stop request signal.
Quick charger communica-
tion error.
Perform self-diagnosis of PDM
(Power Delivery Module).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст