Nissan Leaf. Instruction — part 1290
ID REGISTRATION CANNOT BE COMPLETED
WT-39
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000010120205
The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000010120206
1.
CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL
Check tire pressure sensor activation tool.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sen-
sor activation tool.
2.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
Is tire pressure sensor ID registration completed?
YES
>> Inspection End.
NO
>> GO TO 3.
3.
CHECK TIRE PRESSURE SIGNAL
Change the work location and perform ID registration again.
NOTE:
Depending on the tire pressure sensor position*, a blind spot exists, and the remote keyless entry receiver
gets poor reception. If an ID registration is performed under this condition, the registration may not be com-
pleted. In such case, follow the instructions below to improve the radio wave receiving environment.
• Rotate tire by 90
°, 180°, or 270°. (This Step is to change tire pressure sensor position.)
• Open the door close to the tire of which ID registration is ongoing.
*: Radio wave reception condition depends on vehicle architecture (e.g. body harness layout, tire wheel
design) or environment.
When ID registration is performed, which wheels do not react?
All wheels react and ID registration is possible.>>Inspection End.
Only certain wheel(s) do not react.>>Replace applicable tire pressure sensor. Refer to
All
wheels
do
not
react.>>Check the remote keyless entry receiver. Refer to
WT-40
< SYMPTOM DIAGNOSIS >
EASY FILL TIRE ALERT DOES NOT ACTIVATE
EASY FILL TIRE ALERT DOES NOT ACTIVATE
Description
INFOID:0000000010431154
The Easy Fill tire alert does not function while inflating a tire when the select lever position is in P-range with
the power switch ON or with the vehicle set to READY.
NOTE:
• After starting to inflate the tire, it takes a few seconds for the Easy Fill tire alert to function.
• If there is no response for approximately 15 seconds or more after inflating the tires, cancel the use of the
Easy Fill tire alert function or move the vehicle approximately 1 m (3.2 ft) backward or forward to try again.
The air filler pressure may be weak or out of service area.
• For Easy Fill tire alert, Refer to
WT-11, "Easy Fill Tire Alert Function"
Diagnosis Procedure
INFOID:0000000010431155
1.
LOCATION CHANGE
Move the vehicle to other area and repeat the procedure of the Easy Fill tire alert function. Refer to
"Easy Fill Tire Alert Function"
Is the function normal?
YES
>> Normal (the Easy Fill tire alert may not operate, depending on reception condition.)
NO
>> GO TO 2.
2.
PERFORM BCM SELF DIAGNOSTIC RESULT
With CONSULT
Perform “Self Diagnostic Result”“ for “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK HAZARD WARNING LAMP OPERATION
Check hazard warning lamp operation with hazard switch.
Does the hazard warning lamp blink?
YES
>> GO TO 4.
NO
>> Perform diagnosis for the hazard warning lamp. Refer to
EXL-112, "Diagnosis Procedure"
.
4.
PERFORM ELECTRIC SHIFT CONTROL MODULE SELF DIAGNOSTIC RESULT
With CONSULT
Perform “Self Diagnostic Result”“ for “SHIFT”.
Is any DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
.
NO
>> GO TO 5.
5.
CHECK HORN OPERATION
Check horn operation. Refer to
SEC-102, "Component Function Check"
.
Is the operation normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning components.
6.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
1. Drive for 10 minutes at a speed of 40 km/h (25 MPH) or more.
CAUTION:
Total time driving at a speed of 40 km/h (25 MPH) or more must be 10 minutes.
2. Stop the vehicle.
3. Perform “Self Diagnostic Result”“ for “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
.
EASY FILL TIRE ALERT DOES NOT ACTIVATE
WT-41
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NO
>> Replace BCM. Refer to
WT-42
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010120209
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference
"
—
—
an
d
an
d
—
—
(wit
h h
ea
ted
s
tee
rin
g wh
ee
l)
Possible cause and SUSPECTED PARTS
Imp
rop
er i
ns
ta
lla
tio
n,
lo
os
en
es
s
O
ut
-of-ro
un
d
Un
ba
la
nc
e
Incorrect t
ire
pressure
Uneven tire
wear
Def
orm
ati
on
o
r da
ma
ge
No
n-u
n
iformi
ty
In
co
rrec
t t
ire
si
ze
FRONT A
X
LE
AND FRONT SUSP
ENSION
REAR A
X
LE
AND REAR SUSP
ENSION
TI
RE
ROAD WHEE
LS
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
TIRE
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
Shimmy, Judder
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст