Nissan Leaf. Instruction — part 663
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-253
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Perform the “Self Diagnostic Result” with CONSULT before the symptom diagnosis. Perform the trou-
ble diagnosis if any DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp (HI) is not
turned ON.
One side
• Fuse
• Halogen bulb (HI)
• Harness between IPDM E/R
and headlamp (HI)
• Harness between headlamp
(HI) and ground
• IPDM E/R
Headlamp (HI) circuit
Refer to
TIME RUNNING LIGHT SYSTEM :
Component Function Check"
.
• Harness between IPDM E/R
and daytime running light relay
• Daytime running light relay
• IPDM E/R
Daytime running light relay circuit
Refer to
RUNNING LIGHT SYSTEM : Com-
ponent Function Check"
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
EXL-256, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diag-
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEAD LAMP)
Active test “HEADLAMP”
Headlamp (LO) is not
turned ON.
One side
• Fuse
• halogen bulb (LO)
• Harness between IPDM E/R
and headlamp lamp (LO)
• Harness between headlamp
(LO) and ground
• IPDM E/R
Headlamp (LO) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
EXL-258, "Diagnosis Procedure"
Each lamp is not turned ON/OFF with lighting switch
AUTO.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Combination switch
Refer to
.
• Optical sensor
• Harness between optical sen-
sor and BCM
• BCM
Optical sensor
Refer to
.
Daytime running light is not turned ON.
[Headlamp (HI) is turned ON.]
• Fuse
• Harness between IPDM E/R
and daytime running light relay
• Daytime running light relay
• IPDM E/R
• BCM
• ECM
• Combination meter
• Daytime running light relay circuit
Refer to
TIME RUNNING LIGHT SYS-
TEM : Component Function
Check"
• BCM (HEADLAMP)
Data monitor “ENGINE STATE”
• Combination meter
Data monitor “PKB SW”
• BCM (HEADLAMP)
Active test “DAYTIME RUNNING
LIGHT”
Parking lamp is not turned ON.
• Fuse
• Parking lamp bulb
• Harness between IPDM E/R
and front combination lamp
• IPDM E/R
Parking lamp circuit
Refer to
.
EXL-254
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Front side marker lamp is not turned ON.
• Front side marker lamp bulb
• Harness between IPDM E/R
and front side marker lamp
• Harness between front side
marker lamp and ground
• IPDM E/R
Front side marker lamp circuit
Refer to
.
Tail lamp (Rear side marker lamp) is not turned ON.
• Fuse
• Tail lamp bulb
• Harness between IPDM E/R
and rear combination lamp
• Harness between and rear
combination lamp and ground
Tail lamp circuit
Refer to
.
License plate lamp is not turned ON.
• License plate lamp bulb
• Harness between IPDM E/R
and license plate lamp
• Harness between license plate
lamp and ground
License plate lamp circuit
Refer to
.
Parking lamp, side marker lamp, tail lamp and li-
cense plate lamp are not turned ON.
Symptom diagnosis
“PARKING, SIDE MARKER, LICENSE PLATE AND TAIL LAMPS ARE
NOT TURNED ON”
Refer to
EXL-259, "Diagnosis Procedure"
Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)
Combination meter
• Combination meter
Data monitor “LIGHT IND”
• BCM (HEADLAMP)
Active test “TAIL LAMP”
Turn signal lamp does not
blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms high flasher acti-
vation.)
• Turn signal lamp bulb
• Door mirror
• Harness between BCM and
each turn signal lamp
• Harness between each turn sig-
nal lamp and ground
Turn signal lamp circuit
Refer to
.
Indicator lamp is includ-
ed.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Combination switch
Refer to
.
Turn signal indicator lamp
does not blink.
(Turn signal lamp is nor-
mal.)
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp sig-
nal
• BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with power switch OFF)
• Combination meter power sup-
ply and ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between hazard
switch and BCM
• Harness between hazard
switch and ground
• BCM
Hazard switch circuit
Refer to
.
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between IPDM E/R
and front fog lamp
• Harness between front fog lamp
and ground
• IPDM E/R
Front fog lamp circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
EXL-260, "Diagnosis Procedure"
Symptom
Possible cause
Inspection item
NORMAL OPERATING CONDITION
EXL-255
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000010121472
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area, etc.) while using the auto light system. This is caused by the control difference.
This is normal.
EXL-256
< SYMPTOM DIAGNOSIS >
[HALOGEN HEADLAMP]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Description
INFOID:0000000010121473
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000010121474
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “HL HI REQ” in “Data Monitor” of “IPDM E/R”.
2. While operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-72, "Removal and Installation"
3.
HEADLAMP (HI) CIRCUIT INSPECTION
Check headlamp (HI) circuit. Refer to
EXL-224, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Compo-
Is the inspection result normal?
YES
>> Refer to
GI-53, "Intermittent Incident"
.
NO
>> Repair or replace the malfunctioning part.
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Description
INFOID:0000000010121475
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000010121476
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “HL HI REQ” in “Data monitor” of “IPDM E/R”.
2. While operating the lighting switch, check the monitor status.
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
On
LO
Off
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
On
LO
Off
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст