Nissan Leaf. Instruction — part 421
REAR DOOR
DLK-179
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door hinge rotating part for poor lubrication. If neces-
sary, apply a suitable multi-purpose grease.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000010119876
REMOVAL
1. Fully close the rear door window.
2. Remove rear door finisher. Refer to
INT-22, "Removal and Installation"
.
3. Remove the rear door speaker. Refer to
AV-71, "Removal and Installation"
AV-492, "Removal and Installation"
(NAV-
IGATION WITH BOSE).
4. Remove the door check link bolt (body side).
5. Remove the door check link bolts (door side).
6. Remove door check link (1) from door panel (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check the rear door open/close and lock/unlock operation.
• Check door check link rotating part for poor lubrication. If
necessary, apply a suitable multi-purpose grease.
: Grease point
JMKIA6553ZZ
JMKIA6420ZZ
: Grease point
JMKIA6554ZZ
DLK-180
< REMOVAL AND INSTALLATION >
BACK DOOR
BACK DOOR
Exploded View
INFOID:0000000010119877
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010119878
CAUTION:
• Use two people when removing or installing the back door due to its heavy weight.
• Use shop cloths to protect surrounding components from damage during removal or installation of
the back door.
REMOVAL
1. Remove the rear pillar finishers (LH/RH). Refer to
INT-31, "REAR PILLAR FINISHER : Removal and
.
1.
Back door weather-strip
2.
Back door stay assembly
3.
Back door stay lower bracket
4.
Bumper rubber
5.
Bolt
6.
Back door striker
7.
Back door panel
8.
Back door hinge
A.
Center mark
B.
Seam
Grease
AWKIA2941ZZ
BACK DOOR
DLK-181
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Disconnect harness connector (A) and (B).
3. Remove harness clip (C).
4. Remove ground cable mounting bolt (D).
: Front
5. Remove rear washer hose (1) from hose joint (2).
: Front
6. Remove grommet (1), and then pull out harness from rear
fender extension (LH) (2).
7. Remove grommet (1), and then pull out harness from rear
fender extension (RH) (2).
8. Support back door with appropriate material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
9. Remove back door stay assembly (back door side). Refer to
DLK-184, "BACK DOOR STAY : Removal
10. Remove back door hinge nuts on back door and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
JMKIA6403ZZ
JMKIA6404ZZ
JMKIA6405ZZ
JMKIA6406ZZ
DLK-182
< REMOVAL AND INSTALLATION >
BACK DOOR
• Check back door hinge rotating part for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After installation, check back door open/close and lock/unlock operation. If necessary, perform the
back door assembly adjustment procedure. Refer to
DLK-182, "BACK DOOR ASSEMBLY : Adjust-
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000010119879
1.
Back door assembly
2.
Bumper rubber
3.
Back door hinge
4.
Back door striker
5.
Bolt
6.
Roof panel
AWKIA2942ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст