Nissan Leaf. Instruction — part 379
PRECAUTIONS
DLK-11
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Check that the charge status indicator lamp does not blink and wait for 5 minutes or more.
NOTE:
If the battery is removed within 5 minutes after the power switch is turned OFF, plural DTCs may be
detected.
4. Remove 12V battery within 1 hour after turning the power switch OFF
→ ON → OFF.
NOTE:
• The 12V battery automatic charge control may start automatically even when the power switch is in
OFF state.
• Once the power switch is turned ON
→ OFF, the 12V battery automatic charge control does not start for
approximately 1 hour.
CAUTION:
• After all doors (including back door) are closed, if a door (including back door) is opened before
battery terminals are disconnected, start over from Step 1.
• After turning the power switch OFF, if “Remote A/C” is activated by user operation, stop the air
conditioner and start over from Step 1.
Precaution for Work
INFOID:0000000010119701
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
DLK-12
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010119702
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(J-39570)
Chassis Ear
Locating the noise
—
(J-50397)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
—
(J-46534)
Trim Tool Set
Removing trim components
—
(J-43241)
Remote Keyless Entry
Tester
Used to test keyfobs
SIIA0993E
ALJIA1232ZZ
AWJIA0483ZZ
LEL946A
PREPARATION
DLK-13
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Commercial Service Tools
INFOID:0000000010119703
—
(J-50190)
Signal Tech II
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS
transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob relative
signal strength
• Check Intelligent Key relative signal strength
• Confirm vehicle Intelligent Key antenna sig-
nal strength
• Compatible with future sensors
• Equipped with a display
KV48105501
(J-45295-A)
Transmitter Activation Tool
• Activate TPMS transmitter IDs
• Compatible with future sensors
• Equipped with a display (KV48105501 only)
Tool number
(TechMate No.)
Tool name
Description
ALEIA0131ZZ
ALEIA0183ZZ
Tool name
Description
Insulated gloves
[Guaranteed insulation per-
formance for 1000V/300A]
Removing and installing high voltage compo-
nents
Leather gloves
[Use leather gloves that can
fasten the wrist tight]
• Removing and installing high voltage com-
ponents
• Protect insulated gloves
Insulated safety shoes
Removing and installing high voltage compo-
nents
Safety glasses
[ANSI Z87.1]
• Removing and installing high voltage com-
ponents
• To protect eye from the spatter on the work
to electric line
JMCIA0149ZZ
JPCIA0066ZZ
JPCIA0011ZZ
JPCIA0012ZZ
DLK-14
< PREPARATION >
PREPARATION
Face shield
• Removing and installing high voltage com-
ponents
• To protect eye from the spatter on the work
to electric line
Insulated helmet
Removing and installing high voltage compo-
nents
Power tool
Loosening nuts, screws and bolts
Tool name
Description
JPCIA0167ZZ
JPCIA0013ZZ
PIIB1407E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст