Nissan Leaf. Instruction — part 1056
FRONT SEAT
SE-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4. Release pawls in order as shown (
) and remove the rear
heated seat switch finisher from seatback (passenger seat only).
: Pawl
5. Release the headrest holder locks as shown and remove the
headrest holders.
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left).
6. Remove the seatback from the seat frame assembly.
a. Remove and discard the side air bag module nuts (A).
CAUTION:
Do not reuse the side air bag module nuts.
b. Unclip the side air bag module harness from the seat frame
assembly and route the harness through the seat cushion trim.
NOTE:
Take note of harness routing and attachment location for correct
installation.
c. Disconnect the harness connector from the seatback heater and
unclip from the seat frame assembly.
NOTE:
Take note of harness routing and attachment location for correct installation.
d. Release the side air bag module studs from the seat frame assembly and lift the seatback from the seat
frame assembly.
7. Remove the side air bag module from the seatback.
a. Open the seatback and release the side air bag module studs
(A) from the holes in the chute (1).
b. Pull the side air bag module (2) out of the chute (1) and remove.
CAUTION:
• Do not damage the seatback trim or chute.
JMJIA6587ZZ
PIIB4084J
JMJIA8327ZZ
JMJIA5997ZZ
SE-32
< REMOVAL AND INSTALLATION >
FRONT SEAT
• Place side air bag module as a unit with side air bag
deployment surface facing upward (stud bolts facing
downward). (This is to prevent accidental deployment.)
: Upward
• Replace the side air bag module if it has been dropped or
sustains an impact.
• Do not strike the side air bag module.
ASSEMBLY
Assembly is in the reverse order of disassembly.
Tighten the side air bag nuts to specification. Refer to
CAUTION:
• Check that side air bag module (1) and chute (2) is in the position as shown in the figure.
: Front
• Do not reuse the side air bag module nuts.
• Inspect seatback pad, seatback trim and chute. Replace if damaged.
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the self diagnosis using the air bag warning lamp or CONSULT. Refer to
or
• When installing the side air bag module, make sure there are no wrinkles and the chute is not folded,
twisted or pinched.
SEAT CUSHION
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000010122962
DISASSEMBLY
JMHIA1748ZZ
PHIA1183J
JMJIA8679ZZ
FRONT SEAT
SE-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat cushion repair. It can lead
to personal injury if the side air bag module should accidentally deploy.
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both 12V battery terminals and wait at
least three minutes.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• During disassembly, do not damage the seatback cover, chutes, connectors, retainers, clips, module
harness or the side air bag module.
1. Remove the front seat assembly. Refer to
SE-29, "Removal and Installation"
.
2. Remove recline lever finisher.
a. Apply protective tape (A) on the parts to protect it from damage.
b. Pull out the recline lever finisher while pushing the tip down.
3. Remove lift lever (driver side only).
a. Release pawls using a suitable tool (A) and remove the lift lever
finisher (1).
: Pawl
JMJIA8341ZZ
JMJIA8342ZZ
AWJIA1040ZZ
SE-34
< REMOVAL AND INSTALLATION >
FRONT SEAT
b. Remove screws (A) and the lift lever (1).
4. Release clips and pawls, then remove the seat cushion outer
finisher (1).
: Clip
: Pawl
5. Release clips and pawls, then remove the seat cushion outer
finisher (1).
: Clip
: Pawl
6. Release the seatback trim strap (A) and J-hook retainers (B).
7. Release J-clip retainer (A) unzip the seatback zippers (B).
AWJIA1041ZZ
AWJIA1042ZZ
AWJIA1043ZZ
JMJIA8332ZZ
JMJIA5055ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст