Nissan Leaf. Instruction — part 844
RADIATOR
HCO-15
< REMOVAL AND INSTALLATION >
D
E
F
G
H
I
J
K
L
M
A
B
HCO
N
O
P
Removal and Installation
INFOID:0000000010119133
REMOVAL
WARNING:
Do not remove the reservoir tank cap if the drive motor or other high voltage part is hot. Hot liquid may
spray out from the radiator, causing serious injury.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove front under cover. Refer to
EXT-23, "FRONT UNDER COVER : Removal and Installation"
.
2. Remove the fender protector. Refer to
EXT-21, "FENDER PROTECTOR : Removal and Installation"
.
3. Remove the apron bracket. Refer to
EXT-13, "Removal and Installation"
4. Drain coolant from radiator drain plug. Refer to
5. Remove the radiator upper grille. Refer to
DLK-165, "RADIATOR UPPER GRILLE : Removal and Installa-
6. Remove the washer tank inlet. Refer to
7. Disconnect the water temperature sensor connector. .
8. Remove the reservoir tank.
9. Disconnect the radiator hose (upper front) .
10. Remove the condenser bolt . (Models without heat pump sys-
tems)
: Front
JSCIA0525ZZ
: Front
JSCIA0526ZZ
: Radiator hose (upper rear)
JSCIA0527ZZ
HCO-16
< REMOVAL AND INSTALLATION >
RADIATOR
11. Remove the radiator bolt (top left) .
12. Use rope or other means to support the condenser with the
radiator core support assembly.
13. Remove the air guide bottom clips .
14. Remove the radiator core support lower. Refer to
DLK-163, "RADIATOR CORE SUPPORT LOWER :
.
CAUTION:
Be careful not to damage the radiator core.
15. Lift up the chipping guard and disconnect the parts which
mate with the radiator.
: Front
JSCIA0528ZZ
: Front
JSCIA0529ZZ
JSCIA0530ZZ
JSCIA0534ZZ
RADIATOR
HCO-17
< REMOVAL AND INSTALLATION >
D
E
F
G
H
I
J
K
L
M
A
B
HCO
N
O
P
16. Remove the radiator bolts .
17. Press the radiator top left tab while lowering the radiator downwards to disengage it from the con-
denser . (Models without heat pump systems)
CAUTION:
Because there is a risk of bending the air conditioner pipe, do not lift up the capacitor more than is
necessary to disengage it.
18. Disconnect the radiator side of the radiator hose (lower).
19. Remove the radiator by pulling it out downwards from between
the chipping guard and condenser.
CAUTION:
Be careful not to damage the condenser core.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Be sure to perform correct air bleeding after adding coolant. Refer to
.
Radiator
JSCIA0535ZZ
JSCIA0536ZZ
JSCIA0537ZZ
HCO-18
< REMOVAL AND INSTALLATION >
RADIATOR
• When installing the radiator, securely insert the engaging points shown by the arrows (
) in the figure.
(Models without heat pump systems)
Chipping Guard
• When installing the chipping guard, securely insert the engaging points shown by the arrows (
) in the fig-
ure.
Radiator Hose / Water Hose
• When inserting the radiator hose and water hose, insert all the way until it contacts the end, regardless of
whether or not there is a stopper .
JSCIA0538ZZ
JSCIA0539ZZ
With stopper
No stopper
JPCIA0358ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст