Nissan Leaf. Instruction — part 465

P33DF BAT VOLTAGE ISOLATION SEN

EVB-143

< DTC/CIRCUIT DIAGNOSIS >

D

E

F

G

H

I

J

K

L

M

A

B

EVB

N

O

P

P33DF BAT VOLTAGE ISOLATION SEN

DTC Logic

INFOID:0000000010121142

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Power switch ON and wait for 10 seconds or more.

2. Select “Self Diagnostic Result” of “HV BAT”.

3. Check DTC.
Is P33DF detected?

YES

>> Refer to

EVB-143, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010121143

When this DTC is detected, replace Li-ion battery controller. Refer to

EVB-201, "LI-ION BATTERY CONTROL-

LER : Removal and Installation"

.

DTC

Trouble diagnosis name

DTC detecting condition

Possible causes

P33DF

BAT VOLTAGE ISOLA-
TION SEN

Signal voltage of the on-board isolation resistance moni-
toring system is too high.

Li-ion battery controller

EVB-144

< DTC/CIRCUIT DIAGNOSIS >

P33E0 BAT VOLTAGE ISOLATION SEN

P33E0 BAT VOLTAGE ISOLATION SEN

DTC Logic

INFOID:0000000010121144

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Power switch ON and wait for 10 seconds or more.

2. Select “Self Diagnostic Result” of “HV BAT”.

3. Check DTC.
Is P33E0 detected?

YES

>> Refer to

EVB-144, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010121145

When this DTC is detected, replace Li-ion battery controller. Refer to

EVB-201, "LI-ION BATTERY CONTROL-

LER : Removal and Installation"

.

DTC

Trouble diagnosis name

DTC detecting condition

Possible causes

P33E0

BATTERY VOLTAGE ISO-
LATION SENSOR

Signal Voltage of the on-board isolation resistance mon-
itoring system is too low.

Li-ion battery controller

P33E1 BAT VOLTAGE ISOLATION SEN

EVB-145

< DTC/CIRCUIT DIAGNOSIS >

D

E

F

G

H

I

J

K

L

M

A

B

EVB

N

O

P

P33E1 BAT VOLTAGE ISOLATION SEN

DTC Logic

INFOID:0000000010121146

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Power switch ON and wait for 10 seconds or more.

2. Select “Self Diagnostic Result” of “HV BAT”.

3. Check DTC.
Is P33E1 detected?

YES

>> Refer to

EVB-145, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010121147

When this DTC is detected, perform Li-ion battery insulation resistance loss check. Refer to

EVB-163, "Com-

ponent Inspection"

.

DTC

Trouble diagnosis name

DTC detecting condition

Possible causes

P33E1

BATTERY VOLTAGE ISO-
LATION SENSOR

Signal voltage of the on-board isolation resistance moni-
toring system exhibits no amplitude variation.

Li-ion battery controller

EVB-146

< DTC/CIRCUIT DIAGNOSIS >

P33E2 BATT PACK OVER TEMP

P33E2 BATT PACK OVER TEMP

DTC Logic

INFOID:0000000010121148

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1. Power switch ON and wait for 10 seconds or more.

2. Select “Self Diagnostic Result” of “HV BAT”.

3. Check DTC.
Is P33E2 detected?

YES

>> Refer to

EVB-146, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010121149

1.

PERFORM THE SELF-DIAGNOSIS OF LI-ION BATTERY CONTROLLER

With CONSULT

1. Select “Self Diagnostic Result” of “HV BAT”.

2. Check to see if “P33EB” is detected simultaneously with “P33E2”.
Is P33EB detected?

YES

>> Perform diagnosis on the detected “P33EB”. Refer to

EVB-154, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK BATTERY TEMPERATURE SENSOR

With CONSULT

Using FREEZE FRAME DATA (FFD), check the values of three temperature sensors when DTC is detected.

Is there temperature increase?

Temperature increase is seen>>Replace Li-ion battery. Refer to

EVB-201, "LI-ION BATTERY CONTROL-

LER : Removal and Installation"

.

Temperature increase is not seen>>Replace battery temperature sensors. Refer to

EVB-190, "BATTERY

PACK UPPER CASE : Exploded View"

.

DTC

Trouble diagnosis name

DTC detecting condition

Possible causes

P33E2

BATTERY PACK OVER
TEMPERATURE

When the battery (battery pack) temperature is excessively
high.

Overcharge caused by traction
motor inverter/VCM malfunction

Monitor item

Condition

Limit

Battery temperature sensor 1

Power switch ON

55

°C (131°F) or less

Battery temperature sensor 2

Battery temperature sensor 4