Nissan Leaf. Instruction — part 385
SYSTEM (BACK DOOR OPENER SYSTEM)
DLK-35
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYSTEM (BACK DOOR OPENER SYSTEM)
System Description
INFOID:0000000010119730
SYSTEM DIAGRAM
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed:
NOTE:
• When 12V battery terminal is disconnected and reconnected during all doors unlock state, back door may
not open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after 12V battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When 12V battery terminal is reconnected and back door does not open, have BCM recognize that all doors
are in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• When back door opener switch is pressed while all doors are in unlock status.
• Vehicle speed is less than 5 km/h (3 MPH)
DLK-36
< SYSTEM DESCRIPTION >
SYSTEM (HOMELINK UNIVERSAL TRANSCEIVER)
SYSTEM (HOMELINK UNIVERSAL TRANSCEIVER)
System Description
INFOID:0000000010119731
Item
Function
HomeLink® Universal Transceiver
A maximum of 3 radio signals can be stored and transmitted to operate the garage door, etc.
SYSTEM (CHARGE PORT LID OPEN CONTROL)
DLK-37
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYSTEM (CHARGE PORT LID OPEN CONTROL)
System Description
INFOID:0000000010119732
OPERATION DESCRIPTION
Charge port lid open can be performed by pressing the charge port lid opener button or charge port lid opener
switch. Refer to
DLK-38
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010500887
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
DOOR LOCK
Direct Diagnostic Mode
Description
Ecu Identification
The BCM part number is displayed.
Self Diagnostic Result
The BCM self diagnostic results are displayed.
Data Monitor
The BCM input/output data is displayed in real time.
Active Test
The BCM activates outputs to test components.
Work support
The settings for BCM functions can be changed.
Configuration
• The vehicle specification can be read and saved.
• The vehicle specification can be written when replacing BCM.
CAN Diag Support Mntr
The result of transmit/receive diagnosis of CAN communication is displayed.
System
Sub System
Direct Diagnostic Mode
E
cu
Id
en
tifi
ca
tio
n
Se
lf Di
ag
no
st
ic Re
su
lt
Da
ta
Mo
ni
tor
A
cti
ve
T
est
W
o
rk support
Co
nf
igu
rat
ion
CA
N Diag
Su
pp
ort Mn
tr
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEADLAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
×
Air conditioner
AIR CONDITIONER
×
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст