Nissan Leaf. Instruction — part 211
C1A6F VCM SYSTEM
BR-165
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
7. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
8. Start CONSULT and erase self-diagnosis result of “BRAKE”.
9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
11. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
13. Release brake pedal.
14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6F” detected?
YES
>> GO TO 13.
NO
>> INSPECTION END
13.
CHECK GROUND CIRCUIT
1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
3. Disconnect 12V battery cable from negative terminal. Refer to
BR-6, "Precaution for Removing 12V Bat-
4. Disconnect the electrically-driven intelligent brake unit harness connector.
5. Check the continuity between electrically-driven intelligent brake unit and ground.
Is the inspection result normal?
YES
>> GO TO 15.
NO
>> Repair or replace error-detected parts and GO TO 14.
14.
PERFORM SELF-DIAGNOSIS (6)
With CONSULT
1. Connect the electrically-driven intelligent brake unit harness connector.
2. Connect 12V battery cable to negative terminal.
3. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
4. Repeat step 3 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
7. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
8. Start CONSULT and erase self-diagnosis result of “BRAKE”.
9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
Electrically-driven intelligent brake unit
—
Continuity
Connector
Terminal
E34
32
Ground
Existed
BR-166
< DTC/CIRCUIT DIAGNOSIS >
C1A6F VCM SYSTEM
CAUTION:
Never operate the vehicle while waiting.
11. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
13. Release brake pedal.
14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6F” detected?
YES
>> GO TO 15.
NO
>> INSPECTION END
15.
CHECK DATA MONITOR
With CONSULT
1. Connect the electrically-driven intelligent brake unit harness connector.
2. Connect 12V battery cable to negative terminal.
3. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
4. Repeat step 3 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
5. Start CONSULT and select “BRAKE” and “DATA MONITOR” according this order.
6. Check the “MOTOR POWER SUPPLY” and “CONTROL MODULE POWER”. Refer to
Is the inspection result normal?
YES
>> GO TO 16.
NO
>> Replace the electrically-driven intelligent brake unit. Refer to
BR-510, "Removal and installation"
16.
PERFORM SELF-DIAGNOSIS (7)
With CONSULT
1. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
2. Repeat step 1 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
5. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
6. Start CONSULT and erase self-diagnosis result of “BRAKE”.
7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
9. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
11. Release brake pedal.
12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6F” or “U1000” detected?
YES (“C1A6F”)>>GO TO 1.
C1A6F VCM SYSTEM
BR-167
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
NO
>> INSPECTION END
BR-168
< DTC/CIRCUIT DIAGNOSIS >
C1A70 BRAKE CONTROL SYSTEM
C1A70 BRAKE CONTROL SYSTEM
DTC Logic
INFOID:0000000010123029
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn power switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
2. Repeat step 1 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
5. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
6. Start CONSULT and erase self-diagnosis result of “BRAKE”.
7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
9. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
11. Release brake pedal.
12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A70” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010123030
1.
PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND CONTROL UNIT
Start CONSULT and perform self-diagnosis for “ABS”. Refer to
.
Is any DTC detected?
DTC
Display item
Malfunction detection condition
Possible causes
C1A70
BRAKE CONTROL SYSTEM
Malfunction is detected in ABS actuator and
electric unit (control unit) system.
• Harness or connector
• ABS actuator and electric unit
(control unit)
• Electrically-driven intelligent
brake unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст