Nissan Leaf. Instruction — part 673
SQUEAK AND RATTLE TROUBLE DIAGNOSES
EXT-11
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
PIIB8742E
EXT-12
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000010119986
1.
Screw grommet (RH)
2.
Bumper side bracket (RH)
3.
Bumper reinforcement
4.
Bumper energy absorber
5.
Bumper grille
6.
Front fog lamp (RH) (if equipped)
7.
Spring nut
8.
Bumper fascia
9.
Bumper moulding
10. Bumper cover
11.
J nut
12. Front fog lamp (LH) (if equipped)
13. Screw grommet (LH)
14. Bumper side bracket (LH)
15. Front license plate bracket (Mexico only)
AWKIA2988ZZ
FRONT BUMPER
EXT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000010119987
REMOVAL
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
1. Remove radiator upper grille. Refer to
DLK-165, "RADIATOR UPPER GRILLE : Removal and Installa-
2. Remove charge port cover. Refer to
DLK-158, "CHARGE PORT LID ASSEMBLY : Removal and Installa-
3. Remove bumper fascia upper side mounting bolts (A).
4. Remove bumper fascia upper side fixing clips (A).
5. Remove fender protector mounting bolts (A) and clip (B) (LH/
RH).
6. Remove bumper fascia lower mounting screws.
7. Remove fender protector fixing clips and screws to access bumper fascia assembly fixing screw, and then
remove bumper fascia assembly fixing screws (LH and RH).
: Pawl
: N·m (kg-m, ft-lb)
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA9382ZZ
JMKIA6438ZZ
JMKIA6488ZZ
EXT-14
< REMOVAL AND INSTALLATION >
FRONT BUMPER
8. Apply protective tape on the part to protect it from damage.
9. Pull bumper fascia assembly side toward the vehicle outside as
shown by the arrows in the figure, and then disengage bumper
fascia assembly from bumper side brackets (LH and RH).
CAUTION:
When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.
10. Disconnect front fog lamp harness connectors (LH and RH) (if equipped).
11. Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
12. Remove the following parts after removing bumper fascia.
• License plate bracket
• Front bumper grille
• Front fog lamps (LH and RH). Refer to
EXL-135, "Removal and Installation"
13. Remove bumper energy absorber.
14. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
JMKIA9373ZZ
: Pawl
JMKIA6440ZZ
JMKIA6441ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly – Charge
port lid
A – A
2.1 – 4.5 mm
(0.083 – 0.177 in)
2.0 – 5.0 mm
(0.079 – 0.197 in)
B – B
1.4 – 3.8 mm
(0.091 – 0.303 in)
0.0 – 3.0 mm
(0.000 – 0.118 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст