Nissan Leaf. Instruction — part 872
FLOOR TRIM
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000010119677
Removal and Installation
INFOID:0000000010119678
DANGER:
Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of
electric shock, electric leakage, or similar accidents if the high voltage component and vehicle are
1.
Rear seat back rear panel
2.
Luggage bar assembly
3.
Floor carpet
4.
Carpet hook
5.
Steering column hole cover
6.
Front floor spacer RH
7.
Front floor spacer LH
8.
Front floor center spacer LH
9.
Rear floor spacer LH
10. Rear floor spacer RH
11. Front floor center spacer RH
: Pawl
: N·m (kg-m, ft-lb)
JMJIA5050GB
INT-34
< REMOVAL AND INSTALLATION >
FLOOR TRIM
handled incorrectly. Be sure to follow the correct work procedures when performing inspection and
maintenance.
WARNING:
• Be sure to remove the service plug in order to disconnect the high voltage circuits before perform-
ing inspection or maintenance of high voltage system harnesses and parts.
• The removed service plug must always be carried in a pocket of the responsible worker or placed in
the tool box during the procedure to prevent the plug from being connected by mistake.
• Be sure to wear insulating protective equipment consisting of glove, shoes, face shield and glasses
before beginning work on the high voltage system.
• Never allow workers other than the responsible person to touch the vehicle containing high voltage
parts. To keep others from touching the high voltage parts, these parts must be covered with an insu-
lating sheet except when using them. Refer to
GI-34, "High Voltage Precautions"
CAUTION:
Never bring the vehicle into the READY status with the service plug removed unless otherwise
instructed in the Instruction. A malfunction may occur if this is not observed.
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
WARNING:
Disconnect the high voltage. Refer to
GI-33, "How to Disconnect High Voltage"
1. Check voltage in high voltage circuit. (Check that condenser are discharged.)
a. Lift up the vehicle and remove the Li-ion battery under covers. Refer to
b. Disconnect high voltage harness connector and PTC heater harness connector from front side of Li-ion
battery. Refer to
EVB-181, "Removal and Installation"
.
c.
Measure voltage between high voltage harness connector terminals and PTC heater harness connector
terminals.
DANGER:
Touching high voltage components without using the appropriate protective equipment will
cause electrocution.
CAUTION:
For voltage measurements, use a tester which can measure to 500 V or higher.
2. Remove center console assembly. Refer to
IP-28, "Removal and Installation"
3. Remove front seat assembly (LH and RH). Refer to
SE-29, "Removal and Installation"
4. Remove rear seat cushion. Refer to
SE-40, "SEAT CUSHION : Removal and Installation"
.
5. Remove diagnosis sensor unit. Refer to
SR-38, "Removal and Installation"
.
6. Remove instrument stay.
Standard
: 5 V or less
JPCIA0296ZZ
FLOOR TRIM
INT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Remove instrument stay fixing nuts (A), and then remove instru-
ment stay (1).
7. Disconnect drain hose (2).
CAUTION:
To keep clean the connecting portion and to avoid damage
and foreign materials, cover them completely with plastic
bags, etc. or something similar.
8. Remove shift selector assembly. Refer to
TM-121, "Removal and Installation"
9. Remove electric shift control module. Refer to
TM-121, "Removal and Installation"
.
10. Remove steering column hole cover.
Disengage trim clips (A), and then remove steering column hole
cover.
11. Remove center pillar lower garnish (LH and RH). Refer to
INT-30, "CENTER PILLAR LOWER GARNISH :
.
12. Remove dash side finisher (LH and RH). Refer to
INT-29, "DASH SIDE FINISHER : Removal and Installa-
13. Remove rear foot duct (with rear foot duct). Refer to
VTL-19, "REAR FOOT DUCT 1 : Removal and Instal-
.
14. Remove floor carpet.
NOTE:
Disengage pawls using a suitable tool according to the numerical order 1
→ 2 as shown in the figure, and then
remove carpet hook.
INSTALLATION
Installation is in the reverse order of removal.
AWJIA1052ZZ
JMJIA5140ZZ
: Pawl
JMJIA3620ZZ
INT-36
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Exploded View
INFOID:0000000010119679
1.
Headlining assembly
2.
Assist grip clip
3.
Rear assist grip RH
4.
Front assist grip RH
5.
Sun visor assembly RH
6.
Sun visor cover RH
7.
Sun visor holder
8.
Sun visor cover LH
9.
Sun visor assembly LH
JMJIA5051ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст