Nissan Leaf. Instruction — part 595
EVC-404
< DTC/CIRCUIT DIAGNOSIS >
CHARGE PORT LID OPENER SWITCH
Is the inspection result normal?
YES
>> Replace charge port lid opener switch. Refer to
DLK-211, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
6.
CHECK CHARGE PORT LID OPENER SWITCH POWER SUPPLY
1. Turn power switch OFF.
2. Turn OFF the headlamp.
3. Disconnect charge port lid opener switch harness connector.
4. Check the voltage between charge port lid opener switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 7.
7.
CHECK CHARGE PORT LID OPENER SWITCH SIGNAL CIRCUIT
1. Disconnect VCM harness connector.
2. Check the continuity between charge port lid opener switch harness connector and VCM harness connec-
tor.
3. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-53, "Intermittent Incident"
.
NO
>> Repair or replace error-detected parts.
8.
CHECK CHARGE PORT LID OPENER SWITCH GROUND CIRCUIT
Check the continuity between charge port lid opener switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace error-detected parts.
9.
CHECK CHARGE PORT LID OPENER SWITCH
Check charge port lid opener switch. Refer to
EVC-405, "Component Inspection (Charge Port Lid Opener
.
+
−
Continuity
Charge port lid opener switch
Connector
Terminal
M114
4
Ground
Existed
+
−
Voltage
Charge port lid opener switch
Connector
Terminal
M114
6
Ground
12V battery volt-
age
+
−
Continuity
Charge port lid opener
switch
VCM
Connector
Terminal
Connector
Terminal
M114
6
E123
93
Existed
+
−
Continuity
Charge port lid opener switch
Connector
Terminal
M114
8
Ground
Existed
CHARGE PORT LID OPENER SWITCH
EVC-405
< DTC/CIRCUIT DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace charge port lid opener switch. Refer to
DLK-211, "Removal and Installation"
.
Component Inspection (Charge Port Lid Opener Switch)
INFOID:0000000010120857
1.
CHECK CHARGE PORT LID OPENER SWITCH
1. Turn power switch OFF.
2. Disconnect charge port lid opener switch harness connector.
3. Check the continuity between charge port lid opener switch terminals under the following condition.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace charge port lid opener switch. Refer to
DLK-211, "Removal and Installation"
.
Terminal
Condition
Continuity
6 – 8
Charge port lid opener
switch
Released
Not existed
Pressed
Existed
EVC-406
< DTC/CIRCUIT DIAGNOSIS >
CHARGE PORT LAMP
CHARGE PORT LAMP
Component Function Check
INFOID:0000000010120858
1.
CHARGE PORT LIGHT FUNCTION CHECK
1. Close the charge port lid.
2. Press charge port lid opener switch.
3. Open the charge port lid and check that the charge port light lights up.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
EVC-395, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010120859
1.
CHECK CHARGE PORT LIGHT POWER SUPPLY-1
1. Turn power switch OFF.
2. Disconnect charge port light harness connector.
3. Check the voltage between charge port light harness connector harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK CHARGE PORT LIGHT POWER SUPPLY-2
Check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 3.
3.
CHECK IPDM E/R POWER SUPPLY
Check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Check power supply circuit.
4.
CHECK FUSE
+
−
Voltage
Charge port light
Connector
Terminal
E129
1
Ground
12V battery volt-
age
+
−
Voltage
IPDM E/R
Connector
Terminal
E14
42
Ground
12V battery volt-
age
+
−
Voltage
IPDM E/R
Connector
Terminal
E9
2
Ground
12V battery volt-
age
CHARGE PORT LAMP
EVC-407
< DTC/CIRCUIT DIAGNOSIS >
D
E
F
G
H
I
J
K
L
M
A
B
EVC
N
O
P
1. Pull out #43 fuse.
2. Check that the fuse is not fusing.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-29, "Removal and Installation"
.
NO
>> Replace the fuse after repairing applicable circuit.
5.
CHECK CHARGE PORT LIGHT POWER SUPPLY CIRCUIT
1. Disconnect IPDM E/R harness connector.
2. Check the continuity between IPDM E/R harness connector and charge port light harness connector.
3. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-53, "Intermittent Incident"
.
NO
>> Repair or replace error-detected parts.
6.
CHECK CHARGE PORT LIGHT CONTROL CIRCUIT
1. Close the charge port lid.
2. Press charge port lid opener switch.
3. Check the voltage between charge port light harness connector terminals within 3 minutes of operating
the charge port lid opener switch.
Is the inspection result normal?
YES
>> Replace charge port light. Refer to
INL-58, "Removal and Installation"
.
NO
>> GO TO 7.
7.
CHECK CHARGE PORT LIGHT CONTROL CIRCUIT
1. Disconnect VCM harness connector.
2. Check the continuity between VCM harness connector and charge port light harness connector.
3. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace error-detected parts.
8.
CHECK VCM GROUND CIRCUIT
Check the continuity between VCM harness connector and ground.
+
−
Continuity
IPDM E/R
Charge port light
Connector
Terminal
Connector
Terminal
E14
42
E129
1
Existed
Charge port light
Voltage
Connector
+
−
Terminal
E129
1
2
12V battery volt-
age
+
−
Continuity
VCM
Charge port light
Connector
Terminal
Connector
Terminal
E62
82
E129
2
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст