Nissan Leaf. Instruction — part 207
C1A6D BRAKE POWER SUPPLY BACKUP UNIT
BR-149
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Be sure to wait for 5 seconds or more after turning the power switch OFF.
3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
5. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
6. Start CONSULT and erase self-diagnosis result of “BRAKE”.
7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
9. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
11. Release brake pedal.
12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6D” detected?
YES
>> GO TO 15.
NO
>> INSPECTION END
15.
CHECK BRAKE POWER SUPPLY BACKUP UNIT CIRCUIT
1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
3. Disconnect 12V battery cable from negative terminal. Refer to
BR-6, "Precaution for Removing 12V Bat-
4. Disconnect the electrically-driven intelligent brake unit harness connector.
5. Disconnect the brake power supply backup unit harness connector.
6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.
7. Check the continuity between brake power supply backup unit and ground.
Is the inspection result normal?
YES
>> Replace the brake power supply backup unit. Refer to
BR-513, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
Electrically-driven intelligent brake unit
Brake power supply backup unit
Continuity
Connector
Terminal
Connector
Terminal
E34
31
B15
1
Existed
31
4
Not existed
31
5
Not existed
31
6
Not existed
Brake power supply backup unit
—
Continuity
Connector
Terminal
B15
1
Ground
Not existed
BR-150
< DTC/CIRCUIT DIAGNOSIS >
C1A6E EV SYSTEM
C1A6E EV SYSTEM
DTC Logic
INFOID:0000000010123025
DTC DETECTION LOGIC
DTC REPRODUCTION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn power switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
2. Repeat step 1 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
5. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
6. Start CONSULT and erase self-diagnosis result of “BRAKE”.
7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
9. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
11. Release brake pedal.
12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6E” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010123026
1.
PERFORM VCM SELF DIAGNOSIS
Start CONSULT and perform self-diagnosis for “EV/HEV”. Refer to
.
Is any DTC detected?
YES
>> Check the DTC. Refer to
DTC
Display item
Malfunction detection condition
Possible causes
C1A6E
EV/HEV SYSTEM
Malfunction is detected in the VCM system.
• Harness or connector
• VCM
• Electrically-driven intelligent
brake unit
C1A6E EV SYSTEM
BR-151
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
1. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
2. Repeat step 1 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
5. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
6. Start CONSULT and erase self-diagnosis result of “BRAKE”.
7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
9. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
11. Release brake pedal.
12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6E” detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK 12V BATTERY
1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
3. Check the 12V battery terminal connections. Refer to
BR-6, "Precaution for Removing 12V Battery"
and
.
4. Check the 12V battery. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts and GO TO 4.
4.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
1. Connect 12V battery cable to negative terminal.
2. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
3. Repeat step 2 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
4. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
5. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
BR-152
< DTC/CIRCUIT DIAGNOSIS >
C1A6E EV SYSTEM
Never operate the vehicle while waiting.
6. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
7. Start CONSULT and erase self-diagnosis result of “BRAKE”.
8. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
9. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
10. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
11. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
12. Release brake pedal.
13. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1A6E” detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
CHECK CONNECTOR TERMINALS
1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
3. Disconnect 12V battery cable from negative terminal. Refer to
BR-6, "Precaution for Removing 12V Bat-
4. Disconnect the electrically-driven intelligent brake unit harness connector, then check for failures of pin
terminals and connections.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace error-detected parts and GO TO 6.
6.
PERFORM SELF-DIAGNOSIS (3)
With CONSULT
1. Connect the electrically-driven intelligent brake unit harness connector.
2. Connect 12V battery cable to negative terminal.
3. Turn the power switch OFF to ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
4. Repeat step 3 two or more times.
CAUTION:
Be sure to wait for 5 seconds or more after turning the power switch OFF.
5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
7. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Never set the vehicle to READY.
8. Start CONSULT and erase self-diagnosis result of “BRAKE”.
9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.
10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for
3 minutes or more with all doors closed.
CAUTION:
Never operate the vehicle while waiting.
11. Turn the power switch ON without depressing the brake pedal.
CAUTION:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст